Click here

ECD SYSTEM(w/o EGR System) Cranking Holding Function Circuit

Click here
Click here
DTC Code DTC Name
  Cranking Holding Function Circuit
Click here

DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly*1 or clutch start switch*2 and to terminal STA of the ECM (STA signal).

Tip:

*1: for Automatic Transmission

*2: for Manual Transmission

Click here

WIRING DIAGRAM

Refer to DTC P0617 for w/ Entry and Start System.

Click here

Click here

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (Click here ) and initialization (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK WHETHER ENGINE CAN BE CRANKED


    1. Check if the engine can be cranked.

      Result
      Result Proceed to
      Engine cannot be cranked A
      Engine can be cranked B

  2. Click here

    READ VALUE USING GTS (STARTER SIGNAL)


    1. Connect the GTS to DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.


      1. Powertrain > Engine and ECT > Data List
        Tester Display
        Starter Signal




    5. Check the result when the ignition switch is ON and the engine starts.

      OK
      Switch Condition Starter Signal
      ON OFF
      START ON
      Result
      Proceed to
      OK
      NG

  3. Click here

    INSPECT ST NO. 1 RELAY


    1. Inspect the ST NO. 1 relay.

      Click here

      Result
      Proceed to
      OK
      NG

  4. Click here

    INSPECT STARTER ASSEMBLY


    1. Inspect the starter assembly.


      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)


    1. Remove the ST NO. 1 relay from the engine room relay block and junction block.

    2. Disconnect the starter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST NO. 1 relay terminal 3 - C32-1 (ST) Always Below 1 Ω
      ST NO. 1 relay terminal 3 or C32-1 (ST) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)


    1. Disconnect the starter assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D3-1 (B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)


    1. Remove the ST NO. 1 relay from the engine room relay block and junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

    Tip:

    *1: for Automatic Transmission

    *2: for Manual Transmission


    1. Remove the ST NO. 1 relay from the engine room relay block and junction block.

    2. Disconnect the park/neutral position switch assembly connector.*1

    3. Disconnect the clutch start switch connector.*2

    4. Disconnect the certification ECU (smart key ECU assembly) connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C24-5 (L)*1 - ST NO. 1 relay terminal 2 Always Below 1 Ω
      B2-1*2 - ST NO. 1 relay terminal 2 Always Below 1 Ω
      G70-37 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)


    1. Remove the ST NO. 1 relay from the engine room relay block and junction block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      GO TO ENTRY AND START SYSTEMClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. Click here

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH

    Tip:

    *1: for Automatic Transmission

    *2: for Manual Transmission


    1. Inspect the park/neutral position switch assembly.*1


    2. Inspect the clutch start switch.*2

      Click here

      Result
      Proceed to
      OK
      NG (for Automatic Transmission)
      NG (for Manual Transmission)

  11. Click here

    CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)

    Tip:

    *1: for Automatic Transmission

    *2: for Manual Transmission


    1. Disconnect the park/neutral position switch assembly connector.*1

    2. Disconnect the clutch start switch connector.*2

    3. Disconnect the ECM connector.

    4. Remove the ST NO. 1 relay from the engine room relay block and junction block.

    5. Disconnect the certification ECU (smart key ECU assembly) connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C24-5 (L) - G85-22 (STA)*1 Always Below 1 Ω
      B2-1 - G85-22 (STA)*2 Always Below 1 Ω
      C24-5 (L) or G85-22 (STA) or ST NO. 1 relay terminal 2 or G70-37 (STA) - Body ground and other terminals*1 Always 10 kΩ or higher
      B2-1 or G85-22 (STA) or ST NO. 1 relay terminal 2 or G70-37 (STA) - Body ground and other terminals*2 Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM)

    Tip:

    *1: for Automatic Transmission

    *2: for Manual Transmission


    1. Disconnect the park/neutral position switch assembly connector.*1

    2. Disconnect the clutch start switch connector.*2

    3. Disconnect the certification ECU (smart key ECU assembly) connector.

    4. Disconnect the ECM connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G70-16 (STAR) - C24-4 (B)*1 Always Below 1 Ω
      G70-16 (STAR) - B2-2*2 Always Below 1 Ω
      G70-16 (STAR) - G85-11 (NSW) Always Below 1 Ω
      G70-16 (STAR) or C24-4 (B) or G85-11 (NSW) - Body ground and other terminals*1 Always 10 kΩ or higher
      G70-16 (STAR) or B2-2 or G85-11 (NSW) - Body ground and other terminals*2 Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OK

      GO TO ENTRY AND START SYSTEMClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. Click here

    READ VALUE USING GTS (STARTER SIGNAL)


    1. Connect the GTS to DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.


      1. Powertrain > Engine and ECT > Data List
        Tester Display
        Starter Signal




    5. Check the result when the ignition switch is ON and the engine starts.

      OK
      Switch Condition Starter Signal
      ON OFF
      START ON
      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)