ECD SYSTEM(w/ DPF), Diagnostic DTC:P20CD

DTC Code DTC Name
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit

DESCRIPTION

Refer to DTC P200C

Click here

Tech Tips


  • For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

    Click here

  • If DTC P20CD is present, refer to the DTC table for Diesel Particulate Filter System.

    Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector assembly off, the FIVO output is high for 3 seconds (1 trip detection logic).

  • Open or short in exhaust fuel addition injector assembly circuit

  • Exhaust fuel addition injector assembly

  • ECM

 Comes on DTC stored

Tech Tips

DTC P200C, P200E, P20CF and/or P2428 will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.

MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVO) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVO signal, the ECM judges that the current has been applied to the exhaust fuel addition injector assembly.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVO are inconsistent.

B0025Q7E03
*1 to Exhaust Fuel Addition Injector Assembly
*2 Monitor Circuit
*3 Command Circuit

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CD Ignition switch ON for 3 seconds

WIRING DIAGRAM

B0024AWE03

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses of circuits related to this system before performing the following procedure.

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)


    1. Inspect the exhaust fuel addition injector assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY Click here

    OK

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)


    1. B002538C08
      *a

      Front view of wire harness connector

      (to Exhaust Fuel Addition Injector Assembly)

      Disconnect the exhaust fuel addition injector assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C109-2 - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)


    1. Disconnect the exhaust fuel addition injector assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C109-1 - G85-6 (FIV) Always Below 1 Ω
      C109-1 - G85-6 (FIV) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 11 Click here

    OK

  4. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 13 Click here

  5. CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)


    1. Disconnect the exhaust fuel addition injector assembly connector.

    2. Remove the instrument panel junction block connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C109-2 - 2G-3 Always Below 1 Ω
      C109-2 or 2G-3 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)


    1. Inspect the instrument panel junction block assembly (EFI-MAIN NO. 2).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2) Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - ECM)


    1. Remove the instrument panel junction block connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2P-8 - G85-14 (MREL) Always Below 1 Ω
      2P-8 or G85-14 (MREL) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 11 Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)


    1. Remove the instrument panel junction block connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2K-3 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 11 Click here

    OK

  9. REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY)


    1. Repair or replace harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 13 Click here

  10. REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)


    1. Replace the instrument panel junction block assembly.

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 13 Click here

  11. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 13 Click here

  12. REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY


    1. Replace the exhaust fuel addition injector assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off for 30 seconds or more.

    6. Turn the ignition switch to ON for 3 seconds.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output.


      Powertrain > Engine > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END