Click here

ECD SYSTEM(w/ DPF), Diagnostic DTC:P0504

Click here
Click here
DTC Code DTC Name
P0504 Brake Switch "A" / "B" Correlation
Click here

DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

Tip:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

  • [OFF] denotes ground potential.

  • [ON] denotes battery potential (+B).

  • On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation

Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):

(a) Ignition switch is ON.

(b) Brake pedal is released.

(c) The STP signal is off when the ST1- signal is off.

  • Open or short in stop light switch signal circuit

  • STOP fuse

  • IG2 NO. 3 fuse

  • Stop light switch assembly

  • ECM

 - DTC stored
Table 1. Related Data List
DTC No. Data List
P0504 Stop Light Switch
Click here

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Depress and release brake pedal with ignition switch ON
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Tip:

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  • Stop light switch conditions can be checked using the GTS.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

    5. Check Stop Light Switch when the brake pedal is depressed and released.

Brake Pedal Operation Specified Condition
Depressed ON
Released OFF
Note:

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (Click here ) and initialization (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL B VOLTAGE)


    1. B0027DMC19
      *a

      Front view of wire harness connector

      (to Stop Light Switch)

      Disconnect the stop light switch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A35-2 - Body ground Always 11 to 14 V
      A35-4 - Body ground Ignition switch ON 11 to 14 V

    3. Reconnect the stop light switch connector.

      Result
      Proceed to
      OK
      NG

  2. Click here

    INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  3. Click here

    CHECK ECM (STP AND ST1- VOLTAGE)


    1. B0028IXC05
      *a Brake Pedal Depressed
      *b Brake Pedal Released
      *c

      Component with harness connected

      (ECM)

      Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Brake Pedal Condition Specified Condition
      G86-12 (ST1-) - Body ground Released 7.5 to 14 V
      Depressed 0 to 1.5 V
      G86-13 (STP) - Body ground Released 0 to 1.5 V
      Depressed 7.5 to 14 V
      Result
      Proceed to
      OK
      NG

  4. Click here

    REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

  5. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

  6. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs.


      1. Powertrain > Engine and ECT > Clear DTCs


    3. Turn the ignition switch off.

    4. Turn the ignition switch to ON and turn the GTS on.

    5. Depress and release the brake pedal.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Confirm that the DTC is not output again.


      1. Powertrain > Engine and ECT > Trouble Codes


      Result
      Proceed to
      NEXT

    • NEXT

      END

  7. Click here

    REPLACE STOP LIGHT SWITCH ASSEMBLY


    1. Replace the stop light switch assembly.

      Click here

      Result
      Proceed to
      NEXT