ECD SYSTEM(w/ DPF), Diagnostic DTC:P20CF

DTC Code DTC Name
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open

DESCRIPTION

Refer to DTC P200C Click here.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open

AF Lambda B1S1 is less than 0.85 for a certain time while the engine is running

(1 trip detection logic)

  • Open or short in exhaust fuel addition injector assembly circuit

  • Exhaust fuel addition injector assembly

  • Fuel filter element sub-assembly


    Common Inspection Item:

  • Fuel injection system

  • Intake/Exhaust system

  • After treatment control system

 Comes on DTC stored
Related Data List
DTC No. Data List
P20CF

AF Lambda B1S1

Exhaust Temperature B1S2

Exhaust Temperature B1S3

CONFIRMATION DRIVING PATTERN

P20CF
DTC Detection Drive Pattern PM forced regeneration

MONITOR DESCRIPTION

The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.

If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.

B0026ZIE03

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (See page ) and initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P20CF)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / DTC.


      Powertrain > Engine > Trouble Codes

    5. Read the DTCs.

      Result
      Result Proceed to
      P20CF is output A
      P20CF and other DTCs are output B

      Tech Tips


      • When DTC P20CF and following DTCs are output, uncombusted fuel adhesion to the air fuel ratio sensor due to air fuel ratio sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.

      • DTCs for the air fuel ratio sensor are P2237, P2238, P2239, P2252 and P2253.

        Click here

      • A DTC for fuel leakage is P0093.

        Click here

      • DTCs for the exhaust fuel addition injector assembly wiring malfunction is P20CD.

        Click here

      • A DTC for EGR valve flow malfunction is P0400.

        Click here

      • A DTC for EGR valve stuck open is P042E.

        Click here


    B

    GO TO DTC CHART Click here

    A

  2. CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)

    Note

    If a fuel odor is noted from the white smoke during the inspection, fuel leaks from the exhaust fuel addition injector assembly are suspected.


    1. Disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN NO. 2 fuse for 1 minute or more.

    2. Start the engine and race it to 3000 rpm several times.

    3. Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.

      Result
      Result Proceed to
      White smoke and a fuel odor are present. A
      White smoke and a smell of burning oil are present. B
      Except above C

    B

    CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE Click here

    C

    CHECK FUEL INJECTION SYSTEM Click here

    A

  3. PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1 and Exhaust Temperature B1S3.


      Powertrain > Engine > Data List
      Tester Display
      AF Lambda B1S1
      Exhaust Temperature B1S3

    5. Drive the vehicle until the value of Exhaust Temperature B1S3 becomes 300°C (572°F) or more to activate the air fuel ratio sensors.

      Tech Tips

      Activation of the air fuel ratio sensor can be checked by confirming whether the value of AF Lambda B1S1 has changed from 1.99.

    6. Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

      B0026D7E05

      Tech Tips


      • The air fuel ratio sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

      • Perform diagnosis when the air fuel ratio sensor is operating and active.

      • Normal condition in the illustration is only an example. "AF Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.

      Result
      Result Proceed to
      There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
      Except above B

      Tech Tips

      If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.


    B

    GO TO STEP 10 Click here

    A

  4. REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY


    1. Replace the exhaust fuel addition injector assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY


    1. Clean the fuel filter case and replace the fuel filter.

      Tech Tips

      Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.

      Result
      Proceed to
      NEXT

    NEXT

  6. PERFORM PM FORCED REGENERATION


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    4. Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).

    5. Perform PM forced regeneration.

      Click here

      Result
      PM forced regeneration completes normally.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    GO TO STEP 10 Click here

  7. GO TO DTC CHART


    1. Perform inspection and repair of relevant DTCs.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 9 Click here

  8. CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE


    1. Check for oil leaks and white smoke from the turbocharger sub-assembly and perform any necessary repairs.

      Click here

      Tech Tips

      Other than a malfunction of the turbocharger subassembly, exhaust valve stem oil leaks are suspected.

      Result
      Proceed to
      NEXT

    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    4. Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).

    5. Perform PM forced regeneration.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END

  10. CHECK FUEL INJECTION SYSTEM


    1. Check the fuel injection system.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  11. CHECK INTAKE / EXHAUST SYSTEM


    1. Check the intake/exhaust system.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  12. CHECK AFTER TREATMENT CONTROL SYSTEM


    1. Check the after treatment control system.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 9 Click here