ECD SYSTEM(w/ DPF), Diagnostic DTC:P0016, P0340

DTC Code DTC Name
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
P0340 Camshaft Position Sensor Circuit

DESCRIPTION

The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The G2 signal plate has 3 teeth on its outer circumference and is installed on the exhaust camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm occurs a certain number of times (1 trip detection logic).

  • Camshaft position sensor

  • Crankshaft position sensor

  • Exhaust camshaft

  • ECM

 - DTC stored
P0340 Camshaft Position Sensor Circuit

STA on:


  • No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic).

STA off:


  • This DTC is output when the NE signal indicates a missing tooth 4 times even though the G2 pulse has not occurred once. (1 trip detection logic).

  • Camshaft position sensor

  • Exhaust camshaft

  • ECM

 Comes on DTC stored

Tech Tips


  • If DTC P0016 or P0340 is stored, the following symptoms may appear:


    • Difficulty starting

    • Misfire

    • Combustion noise

    • Black smoke

    • White smoke

    • Lack of power

Reference: Inspection using an oscilloscope.

Tech Tips

The correct waveform is as shown.

B0026RNE01
*a 2 V/DIV.
*b 20 msec./DIV.
ECM Terminal Name

Between G2+ and G2-

Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0016 Idling for 1 seconds or more
P0340

  • Crank engine for 4 seconds (STA on)

  • Idling for 1 seconds or more (STA off)

WIRING DIAGRAM

B0024AAE04
*a Camshaft Position Sensor
*b Crankshaft Position Sensor

CAUTION / NOTICE / HINT

Note

After replacing the ECM, the new ECM needs registration (Click here ) and initialization Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ENGINE CRANKING CONDITION


    1. Check the engine cranking condition.

      Result
      Result Proceed to
      Cranking is OK. A
      Does not crank at all. B

    B

    GO TO PROBLEM SYMPTOMS TABLE Click here

    A

  2. INSPECT ECM (CAMSHAFT POSITION SENSOR)


    1. Inspect the ECM using an oscilloscope.


      1. While the engine is idling, check the waveform between the terminals of the ECM connector.

        B0027C5C04
        *a

        Component with harness connected

        (ECM)

        		 - -
        OK
        Tester Connection Tester Range Condition Specified Condition
        C60-27 (G2+) - C60-18 (G2-)

        2 V/DIV.

        20 msec./DIV.

        		 Idling Correct waveform as shown in illustration
        C60-28 (NE+) - C60-19 (NE-)

        2 V/DIV.

        20 msec./DIV.

        		 Idling Correct waveform as shown in illustration
      Result
      Proceed to
      OK
      NG

    NG

    CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION) Click here

    OK

  3. INSPECT CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITION SENSOR TIMING


    1. Inspect the ECM using an oscilloscope.

    2. While the engine is idling, check the waveform between the terminals of the ECM connector.

    3. Inspect the camshaft position sensor and crankshaft position sensor timing.

      Tech Tips

      The G2 signal is output 3 times for every 2 crankshaft rotations (720°CA).

      B0028Z9E01
      *a 2 V/DIV.
      *b G2 Signal
      *c Ne Signal
      *d 20 msec./DIV.
      OK
      Tester Connection Tester Range Condition Specified Condition
      C60-27 (G2+) - C60-18 (G2-)

      2 V/DIV.

      20 msec./DIV.

      		 Idling Correct waveform as shown in illustration
      C60-28 (NE+) - C60-19 (NE-)

      2 V/DIV.

      20 msec./DIV.

      		 Idling Correct waveform as shown in illustration
      Result
      Proceed to
      OK
      NG

    NG

    CHECK ENGINE MECHANICAL SYSTEM Click here

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine and idle it for 4 seconds or more.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC P0016 or P0340 is output A
      DTC is not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 10 Click here

  6. CHECK ENGINE MECHANICAL SYSTEM


    1. When the G2 signal appears to be malfunctioning, check the exhaust camshaft.


      • If the teeth of the timing rotor are damaged, perform replacement.

        Click here

    2. When the Ne signal appears to be malfunctioning, check the following parts.


      • Installation condition of the crankshaft position sensor

      • Crank angle sensor plate

    3. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 10 Click here

  7. CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)


    1. B0027O2C04
      *a Clearance

      Check the camshaft position sensor installation.

      OK
      Camshaft position sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR Click here

    OK

  8. INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)


    1. Inspect the timing rotor of the exhaust camshaft.

      OK
      Camshaft timing rotor does not have any cracks or deformation.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EXHAUST CAMSHAFT Click here

    OK

  9. REPLACE CAMSHAFT POSITION SENSOR


    1. Replace the camshaft position sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine and idle it for 4 seconds or more.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END

  11. REPLACE EXHAUST CAMSHAFT


    1. Replace the exhaust camshaft.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 10 Click here

  12. SECURELY REINSTALL CAMSHAFT POSITION SENSOR


    1. Securely reinstall the camshaft position sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 10 Click here