Click here

ECD SYSTEM, Diagnostic DTC:P0335, P0339

Click here
Click here
DTC Code DTC Name
P0335 Crankshaft Position Sensor "A" Circuit
P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Click here

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit

When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):

No crankshaft position sensor signal is sent to the ECM while cranking.

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • No. 1 crankshaft position sensor plate (crankshaft)

  • ECM

 Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent

No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):


  • (a) Engine speed is 1000 rpm or more.

  • (b) STA signal is off.

  • (c) 3 seconds or more have elapsed after STA signal is switched from on to off.

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • No. 1 crankshaft position sensor plate (crankshaft)

  • Camshaft timing pulley

  • ECM

 - DTC stored
Table 1. Related Data List
DTC No. Data List
P0335 Engine Speed
P0339
Tip:

  • If DTC P0335 and/or P0339 is stored, the following symptoms may appear:


    • Difficulty starting

    • Misfire

    • Combustion noise

    • Black smoke

    • White smoke

    • Lack of power

Click here

CONFIRMATION DRIVING PATTERN

Table 2. P0335
DTC Detection Drive Pattern Crank or start engine
Table 3. P0339
DTC Detection Drive Pattern Engine running at 1000 rpm or more with vehicle stationary
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

After replacing the ECM, the new ECM needs registration (See page ) and initialization (Click here).

Tip:

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  • The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.

  • A DTC is also stored when the ground of a shielded wire is faulty.

Click here

PROCEDURE


  1. Click here

    INSPECT CRANKSHAFT POSITION SENSOR


    1. Inspect the crankshaft position sensor.

      Click here

      Result
      Proceed to
      OK
      NG

  2. Click here

    CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C84-1 (NE+) - C55-27 (NE+) Always Below 1 Ω
      C84-2 (NE-) - C55-34 (NE-) Always Below 1 Ω
      C84-3 (E) - Body ground Always Below 1 Ω
      C84-1 (NE+) or C55-27 (NE+) - Body ground Always 10 kΩ or higher
      C84-2 (NE-) or C55-34 (NE-) - Body ground Always 10 kΩ or higher

    4. Reconnect the crankshaft position sensor connector.

    5. Reconnect the ECM connector.

      Result
      Proceed to
      OK
      NG

  3. Click here

    CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)


    1. B00247JE01

      Check the sensor installation.

      OK
      Sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

  4. Click here

    CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    1. Check the teeth of the sensor plate.

      OK
      The sensor plate teeth do not have any cracks or deformation.
      Result
      Proceed to
      OK
      NG

  5. Click here

    INSPECT CAMSHAFT TIMING PULLEY


    1. Check the teeth of the camshaft timing pulley.

      OK
      The sensor plate teeth do not have any cracks or deformation.
      Result
      Proceed to
      OK
      NG

  6. Click here

    REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

  7. Click here

    REPLACE CRANKSHAFT POSITION SENSOR


    1. Replace the crankshaft position sensor.

      Click here

      Result
      Proceed to
      NEXT

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

  9. Click here

    SECURELY REINSTALL SENSOR


    1. Securely reinstall the sensor.

      Click here

      Result
      Proceed to
      NEXT

  10. Click here

    REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    1. Replace the No. 1 crankshaft position sensor plate.

      Click here

      Result
      Proceed to
      NEXT

  11. Click here

    REPLACE CAMSHAFT TIMING PULLEY


    1. Replace the camshaft timing pulley.

      Click here

      Result
      Proceed to
      NEXT

  12. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs.


      1. Powertrain > Engine > Clear DTCs


    3. Turn the ignition switch off for 30 seconds or more.

    4. Start the engine and run it at 1000 rpm or more for 5 seconds or more.

    5. Confirm that the DTC is not output again.

      Result
      Proceed to
      NEXT

    • NEXT

      END