CAUTION / NOTICE / HINT
Tech Tips
Perform these procedures after the engine has cooled down.
PROCEDURE
INSPECT TIMING BELT (for 2KD-FTV)
Tech Tips
This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.
REPLACE TIMING BELT
| Type | See procedure |
|---|---|
| 2KD-FTV | |
| 5L-E |
INSPECT TIMING BELT PULLEY (for 2KD-FTV)
Tech Tips
This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.
CLEAN TIMING BELT COVER (for 2KD-FTV)
Tech Tips
This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.
Remove the timing belt cover.
Check that the timing belt cover is not dirty.
If cleaning a timing belt cover, blow compressed air to clean it.
Reinstall the timing belt cover.
INSPECT VALVE CLEARANCE
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 2KD-FTV | |
| 5L-E |
INSPECT DRIVE BELT
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
REPLACE DRIVE BELT (for 5L-E)
Replace the drive belt.
REPLACE ENGINE OIL AND OIL FILTER
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
INSPECT COOLING AND HEATER SYSTEM
Check that the radiator, condenser and/or intercooler is not blocked with leaves, dirt or insects, and clean them if necessary. Also check the hose connection for the installation condition, corrosion, etc.
INSPECT ENGINE COOLANT
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
REPLACE ENGINE COOLANT
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
INSPECT ENGINE OIL COOLER HOSES AND CONNECTIONS (for 1GR-FE)
Check the oil cooler hoses for cracks, leakage, loose connections and deformation.
INSPECT EXHAUST PIPES AND MOUNTINGS
Visually check the pipes, hangers and connections for severe corrosion, leaks or damage.
REPLACE SPARK PLUGS
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1TR-FE | |
| 2TR-FE |
INSPECT BATTERY ELECTROLYTE LEVEL
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
INSPECT WATER SEDIMENT ACCUMULATOR
| Type | See procedure |
|---|---|
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E |
REPLACE FUEL FILTER
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 2KD-FTV | |
| 1TR-FE | |
| 2TR-FE |
INSPECT AIR CLEANER FILTER
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
INSPECT AIR FLOW METER (for 1GD-FTV, 2GD-FTV)
Blow air to the sensor intermittently for approximately 30 seconds.
INSPECT VACUUM PUMP OIL HOSE (for 5L-E)
Check the vacuum pump oil hoses for cracks, leakage, loose connections and deformation.
INSPECT FUEL TANK CAP GASKET
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1GD-FTV | |
| 2KD-FTV | |
| 2GD-FTV | |
| 5L-E | |
| 1TR-FE | |
| 2TR-FE |
INSPECT FUEL LINES, FUEL LINE CONNECTIONS, FUEL TANK VAPOR VENT SYSTEM HOSES AND FUEL TANK BAND
Visually check the fuel lines and hoses for cracks, leakage, loose connections and deformation. Also, visually check the tank band for looseness.
INSPECT CHARCOAL CANISTER
| Type | See procedure |
|---|---|
| 1GR-FE | |
| 1TR-FE | |
| 2TR-FE |