BRAKE SYSTEM (OTHER) SERVICE DATA

Brake Pedal
Brake pedal height from floor panel					167.7 to 177.7 mm (6.603 to 6.996 in.)
Brake pedal free play					1.0 to 6.0 mm (0.0394 to 0.236 in.)
Brake pedal reserve distance from floor panel	w/o ABS	for LHD	for 2WD		90.0 mm (3.54 in.)
		for RHD			91.0 mm (3.58 in.)
	w/ ABS	for LHD (w/o VSC)	for 2WD	except TGN121L-DTTSKV and TGN121L-DTTMKV	87.0 mm (3.43 in.)
				for TGN121L-DTTSKV and TGN121L-DTTMKV	88.0 mm (3.46 in.)
			for 4WD and Pre-Runner	w/o 205R16C tire	91.0 mm (3.58 in.)
				w/ 205R16C tire	92.0 mm (3.62 in.)
		for LHD (w/ VSC)	for 2WD		85.0 mm (3.35 in.)
			for 4WD and Pre-Runner		91.0 mm (3.58 in.)
		for RHD (w/o VSC)	for 2WD		86.0 mm (3.39 in.)
			for 4WD and Pre-Runner	w/o 205R16C tire	90.0 mm (3.54 in.)
				w/ 205R16C tire	91.0 mm (3.58 in.)
		for RHD (w/ VSC)	for 2WD		87.0 mm (3.43 in.)
			for 4WD and Pre-Runner		90.0 mm (3.54 in.)

Brake Master Cylinder (w/ ABS)
Booster push rod and accessory tool clearance	0 mm (0 in.)

Brake Master Cylinder (w/o ABS)
Booster push rod and accessory tool clearance	0 mm (0 in.)

Vacuum Switching Valve (for 1TR-FE, 2TR-FE).
10 MΩ or higher
Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	23 to 26 Ω
1 - Body ground	Always	10 MΩ or higher
2 - Body ground	Always	10 MΩ or higher

Vacuum Pump (for 1GD-FTV, 2GD-FTV)
Negative pressure of vacuum pump assembly	More than 87 kPa (650 mmHg, 25.6 in.Hg)
Minimum lenght A	23.8 mm (0.937 in.)
Minimum lenght B	85.0 mm (3.35 in.)

Vacuum Pump (for 1KD-FTV, 2KD-FTV)
Negative pressure of vacuum pump assembly	More than 87 kPa (650 mmHg, 25.6 in.Hg)

Vacuum Pump (for 5L-E)
Negative pressure of vacuum pump assembly	More than 87 kPa (650 mmHg, 25.6 in.Hg)

Load Sensing Proportioning Valve (w/o ABS)
Load sensing proportioning valve rear axle load	for Single Cab	7354 N (750 kgf, 1651 lbf)
	for Double Cab	8336 N (850 kgf, 1874. lbf)
Standard rear brake fluid pressure		5260 +/-490 kPa (53.6 +/-5.0 kgf/cm², 763 +/-71 psi)
Standard initial length (A)		120 mm (4.72 in.)
Standard length (A) after adjustment		103 to 127 mm (4.06 to 5.00 in.)
Standard pressure change		Changes by 140 kPa (1.4 kgf/cm², 20.3 psi) for every 1 mm (0.0394 in.) change in length A
Standard pressure		2450 kPa (25 kgf/cm², 355 psi)	1350 +/-200 kPa (13.8 +/-2 kgf/cm², 196 +/-49 psi)
		5880 kPa (60 kgf/cm², 853 psi)	2210 +/-340 kPa (22.5 +/-3 kgf/cm², 321 +/-49 psi)

LUBRICANT
Item		Capacity	Classification
Brake fluid	except TSAM Made	-	SAE J1703 or FMVSS No. 116 DOT 3
Brake fluid	for TSAM Made	-	SAE J1704 or FMVSS No. 116 DOT 4