BLACK OUT TAPE(for Rear Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 2 black out tape and No. 3 black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal

    w/ Power Back Door System:

  • Reset back door close position

 Power back door system

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below are for RHD vehicles.

  • Fully open the rear door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR FRAME GARNISH LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  4. REMOVE REAR ARMREST ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  7. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  9. REMOVE REAR DOOR SERVICE HOLE COVER LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  10. REMOVE REAR DOOR GLASS RUN LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  11. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  14. REMOVE REAR DOOR REAR BELT MOULDING LH

    Click here

  15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  16. REMOVE REAR DOOR WEATHERSTRIP LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  17. REMOVE NO. 2 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 2 black out tape LH, heat the rear door panel and No. 2 black out tape LH using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    No. 2 Black Out Tape LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B003OCCC23
    *a Heated Part
    *b Heat Light

    1. B003RY8

      Pull back an edge of the No. 2 black out tape LH and pull it parallel to the rear door panel to remove it.

  18. REMOVE NO. 3 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 3 black out tape LH, heat the rear door panel and No. 3 black out tape LH using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    No. 3 Black Out Tape LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B003OCCC23
    *a Heated Part
    *b Heat Light

    1. B003SA2

      Pull back an edge of the No. 3 black out tape LH and pull it parallel to the rear door panel to remove it.