BLACK OUT TAPE(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal

    w/ Power Back Door System:

  • Reset back door close position

 Power back door system

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below are for RHD vehicles.

  • Fully open the front door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B003JMU

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B003RP6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  4. REMOVE FRONT ARMREST ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  8. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  10. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  12. REMOVE FRONT DOOR GLASS RUN LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

    Click here

  14. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

    Click here

  15. REMOVE FRONT DOOR WEATHERSTRIP LH


    1. B003KSF

      Using a clip remover, detach the clip and remove enough of the upper portion of the front door weatherstrip LH so that the No. 1 black out tape LH can be removed.

  16. REMOVE NO. 1 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 1 black out tape LH, heat the front door panel and No. 1 black out tape LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    No. 1 Black Out Tape LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B003OCCC23
    *a Heated Part
    *b Heat Light

    1. B003MQW

      Pull back an edge of the No. 1 black out tape LH and pull it parallel to the front door panel to remove it.