FRONT SEAT ASSEMBLY(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • B003L4P

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for RHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY RH


    1. B003N30

      Place the front seat assembly RH in the vehicle as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly RH, body exterior or interior parts.

    2. B003PIJC01
      *A w/o Front Seat Airbag
      *B w/ Front Seat Airbag

      w/o Front Seat Side Airbag:


      1. Connect the 2 connectors.

    3. w/ Front Seat Side Airbag:


      1. Connect the 3 connectors.

    4. Attach the wire harness clamp.

    5. w/ Front Seat Side Airbag:

      Connect the front seat airbag assembly RH connector.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B003OC2C02
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • Be careful not to damage the connector or wire harness of the front seat airbag assembly RH.

        • When connecting the connector, make sure to push it straight in.

        • Do not hold any parts other than the yellow CPA when connecting the connector.

        • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

    6. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    7. Temporarily install the front seat assembly RH with the 4 bolts.

    8. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH rearmost position.

    9. B003RRHN01

      Tighten the 2 bolts on the front side of front seat assembly RH in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    10. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the frontmost position.

    11. B003JOZN01

      Tighten the 2 bolts on the rear side of front seat assembly RH in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. INSTALL FRONT SEAT REAR INNER TRACK COVER RH


    1. B003K0CC01
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to attach the guide.

    2. Push in installation direction (2) shown in the illustration to attach the claw and install the front seat rear inner track cover RH.

  3. INSTALL FRONT SEAT REAR OUTER TRACK COVER RH


    1. B003R4EC01
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to attach the guide.

    2. Push in installation direction (2) shown in the illustration to attach the claw and install the front seat rear outer track cover RH.

    3. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the center position.

  4. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Front Seat Side Airbag)

    Airbag System (for Type A):

    Click here

    Airbag System (for Type B):

    Click here

  5. CHECK SRS WARNING LIGHT (w/ Front Seat Side Airbag)

    Airbag System (for Type A):

    Click here

    Airbag System (for Type B):

    Click here

  6. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here