FRONT SEAT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:


  • B003L4P

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for RHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Airbag System (for Type A):

    Click here

    Airbag System (for Type B):

    Click here

    B003JMU

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT REAR OUTER TRACK COVER RH


    1. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the frontmost position.

    2. B003O2TC01
      B003OFB Remove in this Direction (1)
      B003QYY Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    3. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear outer track cover RH.

  3. REMOVE FRONT SEAT REAR INNER TRACK COVER RH


    1. B003QAQC01
      B003OFB Remove in this Direction (1)
      B003QYY Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    2. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear inner track cover RH.

  4. REMOVE FRONT SEAT ASSEMBLY RH


    1. B003JOZ

      Remove the 2 bolts on the rear side of the front seat assembly RH.

    2. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the rearmost position.

    3. B003RRH

      Remove the 2 bolts.

    4. Operate the power seat switch knob RH (for Slide) to slide the front seat assembly RH to the center position.

    5. Operate the power seat switch knob RH (for Vertical) to set the seat cushion height of the front seat assembly RH to the uppermost position.

    6. Operate the power seat switch knob RH (for Reclining) to set the seatback of the front seat assembly RH to the perpendicular position.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B003RP6

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. w/ Front Seat Side Airbag:

      Disconnect the front seat airbag assembly RH connector.


      1. Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

        B003NF0C12
        *1 Slider - -
        *a Push *b Slide
    9. B003PIJC01
      *A w/o Front Seat Side Airbag
      *B w/ Front Seat Side Airbag

      w/o Front Seat Side Airbag:


      1. Disconnect the 2 connectors.

    10. w/ Front Seat Side Airbag:


      1. Disconnect the 3 connectors.

    11. Detach the wire harness clamp.

    12. B003PQI

      Remove the front seat assembly RH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly RH, body exterior or interior parts.