FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • B003L4P

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for RHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY RH


    1. Attach the claw and install the seat track handle sub-assembly RH.

      B003MH3

  2. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH


    1. B003JA0C01
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      While rotating the part in the installation direction (1) shown in the illustration, attach the hook.

    2. Push in the installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly RH.

  3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH


    1. B003RW2C06
      *A for Driver Side
      *B for Front Passenger Side
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to install the guide.

    2. While expanding the part in the installation direction (2) shown in the illustration, attach the claw.

    3. Install the front seat cushion edge protector RH with the screw.

  4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

    Tech Tips

    Use the same procedure as for the RH side.

  5. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)


    1. B003K56C01
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Push in the installation direction (1) shown in the illustration to temporarily install the front seat lower cushion shield RH.

    2. Push in the installation direction (2) shown in the illustration to attach the clip.

    3. B003M9IC01
      B003OFB Install in this Direction

      Push in the guide in the installation direction shown in the illustration.

    4. Install the front seat lower cushion shield RH with the screw.

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

    Tech Tips

    Use the same procedure as for the RH side.

  7. INSTALL SEAT COVER WIRE


    1. B003LGYN04

      Install the seat cover wire.

      Tech Tips


      • There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


      • Refer to the precautions when creating a wire.

        Click here

      Length
      A 170 mm (6.70 in.)
      B 150 mm (5.91 in.)
      C 230 mm (9.06 in.)
      D 270 mm (10.63 in.)
      E 290 mm (11.42 in.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B003N9T

  8. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    Tech Tips


    • Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

      Click here


    • As shown in the illustration, fix all of the cover seam allowances in the same direction.

      B003QNEN02

    1. Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.

    2. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

      B003RP5C01
      *1 Hog Ring Pliers - -
      *a Cutout - -

      Note


      • Do not dirty or damage the separate type front seat cushion cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.

      Tech Tips

      Install the hog rings at the cutouts if they are there.

    3. Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      B003KRLC01
      *1 Hog Ring Pliers - -

      Note


      • Do not dirty or damage the separate type front seat cushion cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.

  9. INSTALL SEAT CUSHION COVER WITH PAD


    1. While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to attach the seat cushion cover with pad.

      B003KY4

  10. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. B003QW3

      Attach the claw to install the 2 front seatback edge protectors.

  11. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY RH


    1. B003M7VC01
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly RH.

    2. Push in the installation direction (1) shown in the illustration to install the front seatback spring sub-assembly RH.

    3. Push in the installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly RH.

    4. B003KMQ

      Attach the claw and install the 2 front seatback edge protectors.

  12. INSTALL FRONT NO. 2 SEATBACK HOOK


    1. B003K1FC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and install the 2 front No. 2 seatback hooks.

  13. INSTALL FRONT SEATBACK HOOK


    1. B003JRL

      Attach the claw and hook to install the 2 front seatback hooks.

  14. INSTALL FRONT SEAT AIRBAG ASSEMBLY RH (w/ Front Seat Side Airbag)

    Click here

  15. INSTALL SEAT COVER WIRE


    1. B003N7UN01

      Install the seat cover wire.

      Tech Tips


      • There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


      • When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


      • Refer to the precautions when creating a wire.

        Click here

      Length
      A 290 mm (11.42 in.)
      B 420 mm (1.38 ft.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B003N9T

  16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    Tech Tips


    • Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.

      Click here


    • As shown in the illustration, fix all of the cover seam allowances in the same direction.

      B003KL0N01

    1. Set the separate type front seatback cover.

    2. Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

      B003KBLC01
      *1 Hog Ring Pliers - -
      *a Cutout - -

      Note


      • Do not dirty or damage the separate type front seatback cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.

      Tech Tips

      Install the hog rings at the cutouts if they are there.

  17. INSTALL SEATBACK COVER WITH PAD


    1. B003J7JC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to temporarily install the seatback cover with pad.

    2. w/ Front Seat Side Airbag:


      1. B003N2BC01
        *1 J Hook A
        *2 J Hook B
        B003OFB Install in this Direction

        Push in the installation direction shown in the illustration to attach the J hook A and J hook B.

      2. B003JG7C01
        *1 J Hook B (J Hook A and J Hook B)
        *2 J Hook C
        B003OFB Install in this Direction

        Push in the installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.

      3. Install a new rivet to J hook B.

        B003JP9C12
        *A for LH seat *B for RH seat
        *1 J Hook A *2 J Hook B

      4. Place your hand at the position shown in the illustration and push in the installation direction to attach the J hook B.

        B003OA0C01
        *1 J Hook A *2 J Hook B
        *3 J Hook C - -
        B003QBX Place Hand Here B003OFB Install in this Direction

  18. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B003PATC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and install the 2 front seat headrest supports.

    2. B003PA8C10
      B003OFB Install in this Direction

      Pull in the installation direction shown in the illustration to attach the guide to the 2 straps.

    3. B003ODRC01
      B003OFB Install in this Direction

      Close the fasteners as shown in the illustration.

    4. Using hog ring pliers, install 6 new hog rings.

      B003LEQC05
      *1 Hog Ring Pliers - -
      *a Cutout - -

      Note


      • Do not dirty or damage the separate type front seatback cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.

      Tech Tips

      Install the hog rings at the cutouts if they are there.

  19. INSTALL FRONT NO. 1 SEATBACK HOOK


    1. B003O8U

      Attach the claw and install the front No. 1 seatback hook.

  20. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. B003PT8C02
      B003OFB Install in this Direction (1)
      B003QYY Install in this Direction (2)

      Push down in the installation direction (1) shown in the illustration.

    2. Rotate the part in the installation direction (2) shown in the illustration and align the guide to install the reclining adjuster inside cover RH.

  21. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    Tech Tips

    Use the same procedure as for the RH side.

  22. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH


    1. B003NICC16
      *A LH Side
      *B RH Side

      Install the 4 bolts and front seatback frame sub-assembly RH.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. B003LL7C11
      *A LH Side
      *B RH Side
      *1 Separate Type Front Seat Cushion Cover

      Attach the 2 hooks.

    3. B003Q42C01
      *1 Wire Harness Clamp
      *2 Connector Clamp

      w/ Front Seat Side Airbag:


      1. Attach the wire harness clamp and connector clamp.

    4. B003NOP

      Install the band in the position shown in the illustration.

  23. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

    Click here

  24. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Driver Side)


    1. B003LNZC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    2. B003Q1ZC01
      B003OFB Install in this Direction

      Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield RH.

  25. INSTALL FRONT SEAT INNER CUSHION SHIELD LH (for Front Passenger Side)


    1. B003JS5C01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    2. B003LA3C02
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield LH.

  26. INSTALL FRONT SEAT CUSHION SHIELD RH (for Driver Side)


    1. B003RHYC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    2. B003JYMC01
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    3. B003JY3C02
      *1 Clip A
      *2 Clip B

      Attach the clip B.

    4. Attach the claw.

    5. Attach the clip A and install the front seat cushion shield RH.

  27. INSTALL FRONT SEAT CUSHION SHIELD LH (for Front Passenger Side)


    1. B003QVDC02
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    2. B003Q4TC02
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration to attach the claw and guide.

    3. B003OETC07
      *1 Clip A
      *2 Clip B

      Attach clip B.

    4. Attach the claw.

    5. Attach clip A.

    6. Install the front seat cushion shield LH with the screw.

  28. INSTALL VERTICAL ADJUSTING HANDLE RH (for Driver Side)


    1. B003LABC01
      B003OFB Install in this Direction

      With the reclining adjuster release handle RH pulled up.

    2. Attach the guide, and then push in the installation direction shown in the illustration to install the vertical adjusting handle RH.

    3. B003NTD

      Install the screw.

  29. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH (for Driver Side)


    1. B003SFUC01
      B003OFB Install in this Direction

      With the reclining adjuster release handle RH pulled up.

    2. Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle RH.

  30. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Front Passenger Side)


    1. B003RT0C02
      B003OFB Install in this Direction

      Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.

  31. INSTALL SEAT ADJUSTER COVER CAP RH


    1. B003O6YC01
      B003OFB Install in this Direction

      Push in installation direction shown in the illustration to install the 2 seat adjuster cover caps RH.

  32. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. B003S0PC01
      B003KT0 Application Area
      B003LF2 Apply Silicon

      Apply silicon lubricant to the application area.

      Tech Tips

      The application area shown in the illustration is 20 + / -10 mm.

    2. Install the front seat headrest assembly.