CURTAIN SHIELD AIRBAG ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B003LFJ

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the curtain shield airbag assembly RH, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of the curtain shield airbag assembly RH, use an unneeded vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B003MXEN26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B003RP6

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    4. Remove the roof headlining assembly.

      Click here

    5. Install SST.


      1. B003OWEC01
        *a Connector Lock
        B003OFB Release in this Direction

        Using a screwdriver, pull up the connector lock and disconnect the airbag connector.

        Note

        When disconnecting the airbag connector, take care not to damage the airbag wire harness.

      2. B003OIJN01

        After connecting the following SST to each other, connect them to the curtain shield airbag assembly RH.

        SST
        09082-00700   ( 09082-10801, 09082-20801 )

        CAUTION:


        • B003KCQ

          Do not deploy the curtain shield airbag assembly RH if it rattles due to looseness and the tightening bolts and clips, etc., for the inflator and deployment part of the curtain shield airbag assembly RH falling off.

        • Do not deploy the curtain shield airbag assembly RH if the deployment part fell off.

        • If the curtain shield airbag assembly RH is deployed when it rattles or parts have fallen off, the curtain shield airbag assembly RH may fly off and cause serious injuries.

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      3. B003RG4C02
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      4. While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B003KU9

        Note

        Take care not to damage the SST wire harness.

      5. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    6. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B003LHO

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    7. Remove the curtain shield airbag assembly RH.

      Click here

      CAUTION:


      • B003LCA

        The curtain shield airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B003ML7

        Do not apply water etc. to a curtain shield airbag assembly RH with a deployed airbag.

      • If water is applied to the curtain shield airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

      • B003R4A

        Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly RH.

      • If the curtain shield airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the curtain shield airbag assembly RH in a plastic bag.

    8. Dispose of the curtain shield airbag assembly RH.


      1. Place the curtain shield airbag assembly RH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B003JH2

          The curtain shield airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B003RBJ

          Do not apply water etc. to a curtain shield airbag assembly RH with a deployed airbag.

        • If water is applied to the curtain shield airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

        • B003RD2

          Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly RH.

        • If the curtain shield airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B003LXK

          Never dispose of a curtain shield airbag assembly RH with an undeployed airbag.

        • If an undeployed curtain shield airbag assembly RH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B003MXEN26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the curtain shield airbag assembly RH.

      Click here

      CAUTION:

      B003RP6

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. B003Q3W

      Cut off the deployment section of the curtain shield airbag assembly RH.

      CAUTION:

      B003RD2

      • Wear safety glasses and gloves.

      • The dust may enter the eyes or be breathed in.

    4. B003LTXC28
      *a Wire Diameter
      *b Stripped Wire

      Using braided wire, tie down the lower curtain shield airbag assembly RH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the lower curtain shield airbag assembly RH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. B003K28C01
        *a Width
        *b Inner Diameter
        *c Outlet

        Position the curtain shield airbag assembly RH inside the tire as shown in the illustration.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tires may be damaged by the airbag deployment, so use unneeded tires.

    5. Install SST.


      1. B003N39N01

        After connecting the following SST to each other, connect them to the curtain shield airbag assembly RH.

        SST
        09082-00802   ( 09082-10801, 09082-20801 )

    6. Place the tires.


      1. B003JMIC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the curtain shield airbag assembly RH is tied.

      2. Place at least 2 tires onto the tire to which the curtain shield airbag assembly RH is tied. The top tire should have a wheel installed.

        Note


        • Do not place the SST connector under the tire because it could be damaged.

        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

      3. B003PY6

        Tie the tires together with the 2 wires.

    7. Install SST.


      1. B003NYKC01
        *a 10 m or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    8. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag assembly RH is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B003R8R

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    9. Dispose of the curtain shield airbag assembly RH.

      CAUTION:


      • B003JH2

        The curtain shield airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B003RBJ

        Do not apply water etc. to a curtain shield airbag assembly RH with a deployed airbag.

      • If water is applied to the curtain shield airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

      • B003RD2

        Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly RH.

      • If the curtain shield airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B003LXK

        Never dispose of a curtain shield airbag assembly RH with an undeployed airbag.

      • If an undeployed curtain shield airbag assembly RH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the curtain shield airbag assembly RH from the tire.

      2. Place the curtain shield airbag assembly RH in a plastic bag, tie it tightly, and dispose of it according to local regulations.