SPIRAL CABLE INSPECTION

PROCEDURE


  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

    • Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.


    1. Visually check for defects with the spiral cable sub-assembly.


      1. The defects are as follows:


        • Scratches

        • Small cracks

        • Dents

        • Chips

        • Cracks or other damage to the connector

        OK
        No defects are found.

        If any of the defects is found, replace the spiral cable sub-assembly with a new one.

    2. Check the spiral cable sub-assembly.

      B003S4NC02
      *A w/ Steering Heater - -
      *a

      Component without harness connected

      (Spiral Cable Sub-assembly)

      		 - -
      B003NOZ Interlock - -

      Note


      • When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

      • As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.


      1. Set the spiral cable sub-assembly to the center position.

        Click here

      2. Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.


        • Inspect the SRS airbag circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          A-1 (D+) - D-2 Always Below 1 Ω
          A-2 (D-) - D-1
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the steering pad switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-3 (EAU) - E-8 Always 3 Ω or less
          B-5 (AU2) - E-10
          B-6 (AU1) - E-11
          B-10 (+DP) - E-2
          B-11 (+DP2) - E-3
          B-13 (IL+2) - E-5
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the horn switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition

          B-9 (HO) - E-1

          *1

          		 Always 3 Ω or less

          B-9 (HO) - F-2

          *2
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Cruise Control Systems:

          Inspect the cruise control circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-1 (CCS) - F-3 Always 3 Ω or less
          B-2 (ECC) - F-4
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Steering Heater:

          Inspect the steering heater circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          G-4 (EHT) - C-4 Always Below 0.1 Ω
          G-3 (BHT) - C-3
          If the result is not as specified, replace the spiral cable sub-assembly.

        *1: w/ Steering Pad Switch:

        *2: w/o Steering Pad Switch:

      3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.


        • Inspect the SRS airbag circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          A-1 (D+) - D-2 Always Below 1 Ω
          A-2 (D-) - D-1
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the steering pad switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-3 (EAU) - E-8 Always 3 Ω or less
          B-5 (AU2) - E-10
          B-6 (AU1) - E-11
          B-10 (+DP) - E-2
          B-11 (+DP2) - E-3
          B-13 (IL+2) - E-5
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the horn switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition

          B-9 (HO) - E-1

          *1

          		 Always 3 Ω or less

          B-9 (HO) - F-2

          *2
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Cruise Control Systems:

          Inspect the cruise control circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-1 (CCS) - F-3 Always 3 Ω or less
          B-2 (ECC) - F-4
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Steering Heater:

          Inspect the steering heater circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          G-4 (EHT) - C-4 Always Below 0.1 Ω
          G-3 (BHT) - C-3
          If the result is not as specified, replace the spiral cable sub-assembly.

        *1: w/ Steering Pad Switch:

        *2: w/o Steering Pad Switch:

      4. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.


        • Inspect the SRS airbag circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          A-1 (D+) - D-2 Always Below 1 Ω
          A-2 (D-) - D-1
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the steering pad switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-3 (EAU) - E-8 Always 3 Ω or less
          B-5 (AU2) - E-10
          B-6 (AU1) - E-11
          B-10 (+DP) - E-2
          B-11 (+DP2) - E-3
          B-13 (IL+2) - E-5
          If the result is not as specified, replace the spiral cable sub-assembly.

        • Inspect the horn switch circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition

          B-9 (HO) - E-1

          *1

          		 Always 3 Ω or less

          B-9 (HO) - F-2

          *2
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Cruise Control Systems:

          Inspect the cruise control circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          B-1 (CCS) - F-3 Always 3 Ω or less
          B-2 (ECC) - F-4
          If the result is not as specified, replace the spiral cable sub-assembly.

        • w/ Steering Heater:

          Inspect the steering heater circuit.

          Standard Resistance
          Tester Connection Condition Specified Condition
          G-4 (EHT) - C-4 Always Below 0.1 Ω
          G-3 (BHT) - C-3
          If the result is not as specified, replace the spiral cable sub-assembly.

        *1: w/ Steering Pad Switch:

        *2: w/o Steering Pad Switch: