AIRBAG SYSTEM(for Type A) Diagnosis Circuit

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

Tech Tips


  • When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

  • A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.

WIRING DIAGRAM

B003KJNE02

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication DTC is output.

      Click here


      Result
      Proceed to
      DTCs are output
      DTC is not output

    DTCs are output

    GO TO CAN COMMUNICATION SYSTEM for LHD: Click here for RHD: Click here

    DTC is not output

  2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)


    1. Turn the ignition switch off.

      B003RZNC02
      *A for 2TR-FE *B for 1GD-FTV, 2GD-FTV
      *C for 1GR-FE *D for 5L-E
      *a

      Front view of wire harness connector

      (to ECM)

      		 *b Front view of DLC3

    2. Disconnect the connector from the ECM.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 2TR-FE
      Tester Connection Condition Specified Condition
      G143-19 (TC) - G7-13 (TC) Always Below 1 Ω
      for 1GD-FTV, 2GD-FTV
      Tester Connection Condition Specified Condition
      G49-25 (TC) - G7-13 (TC) Always Below 1 Ω
      for 1GR-FE
      Tester Connection Condition Specified Condition
      G144-6 (TC) - G7-13 (TC) Always Below 1 Ω
      for 5L-E
      Tester Connection Condition Specified Condition
      G161-17 (TC) - G7-13 (TC) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)


    1. B003Q2JC29
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G7-4 (CG) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      B003KSQC02
      *A for 2TR-FE *B for 1GD-FTV, 2GD-FTV
      *C for 1GR-FE *D for 5L-E
      *a

      Front view of wire harness connector

      (to ECM)

      		 - -
      Standard Resistance
      for 2TR-FE
      Tester Connection Condition Specified Condition
      G143-19 (TC) - Body ground Always 1 MΩ or higher
      for 1GD-FTV, 2GD-FTV
      Tester Connection Condition Specified Condition
      G49-25 (TC) - Body ground Always 1 MΩ or higher
      for 1GR-FE
      Tester Connection Condition Specified Condition
      G144-6 (TC) - Body ground Always 1 MΩ or higher
      for 5L-E
      Tester Connection Condition Specified Condition
      G161-17 (TC) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU