Note
When replacing the combination meter assembly, make sure to replace it with a new one.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
w/ Smart Entry and Start System:
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.
Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | Link |
|---|---|---|
| Speedometer malfunction | Refer to "Speedometer Malfunction" | |
| Tachometer malfunction | Refer to "Tachometer Malfunction" | |
| Fuel receiver gauge malfunction (Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past) |
Refer to "Fuel Receiver Gauge Display Malfunction" | |
| Engine coolant temperature receiver gauge malfunction | Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" |
| Symptom | Suspected Area | Link |
|---|---|---|
| Turn indicator light malfunction (Turn signal light operates normally) | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | |
| Proceed to "Turn Signal Switch Circuit" | ||
| Proceed to "Hazard Warning Switch Circuit" | ||
| Combination meter assembly | ||
| Front fog indicator light malfunction (Front fog light operates normally) (w/ Front Fog Light) | Perform Active Test [Indicat. Lamp Fr FOG] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| Rear fog indicator light malfunction (Rear fog light operates normally) (w/ Rear Fog Light) | Harness or connector | - |
| Combination meter assembly | ||
| Taillight indicator light malfunction (Taillight operates normally) | Perform Active Test [Indicat. Lamp Tail] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| High beam indicator light malfunction (High beam headlight operates normally) | Perform Active Test [Indicat. Lamp Beam] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| Smart entry and start system indicator light malfunction (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Smart System Indicator] | ||
| Perform Active Test [Smart System Warning] | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Cruise indicator light malfunction (w/ Cruise Control System) | Proceed to "Cruise Main Indicator Light Circuit" | |
| Combination meter assembly | ||
| SET indicator light malfunction (w/ Cruise Control System) | Proceed to "Cruise SET Indicator Light Circuit" | |
| Combination meter assembly | ||
| Brake override system warning light malfunction | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Check indicator/warning light | ||
| Perform Active Test [Brake Override Indicator] | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| Seat belt warning light malfunction | Proceed to "Driver Side Seat Belt Warning Light does not Operate" | |
| Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" | ||
| Parking brake warning light malfunction | Perform Active Test [Indicat. Park] | |
| Parking brake switch assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Brake warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Brake] | ||
| Proceed to "Brake Warning Light Remains ON" (w/ VSC) | ||
| Proceed to "Brake Warning Light does not Come ON" (w/ VSC) | ||
| Proceed to "Brake Warning Light Remains ON" (w/o VSC) | ||
| Proceed to "Brake Warning Light does not Come ON" (w/o VSC) | ||
| Harness or connector | - | |
| Brake master cylinder sub-assembly (brake fluid level warning switch) | ||
| Vacuum warning switch assembly (for Diesel Engine) | ||
| Combination meter assembly | ||
| SRS warning light malfunction (w/ Airbag System) | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Airbag] | ||
| Proceed to "SRS Warning Light Remains ON" (Type A) | ||
| Proceed to "SRS Warning Light does not Come ON" (Type A) | ||
| Proceed to "SRS Warning Light Remains ON" (Type B) | ||
| Proceed to "SRS Warning Light does not Come ON" (Type B) | ||
| Combination meter assembly | ||
| Charger system warning light malfunction (for GD Series Engine, TR Series Engine, GR Series Engine) | Perform Active Test [Indicat. Lamp Charge] | |
| Charging system (for 1GD-FTV) | ||
| Charging system (for 2GD-FTV) | ||
| Charging system (for 2TR-FE) | ||
| Charging system (for 1GR-FE) | ||
| Combination meter assembly | ||
| Charger system warning light malfunction (for KD Series Engine, 5L-E) | Harness or connector | - |
| Generator assembly (for 1KD-FTV) | ||
| Generator assembly (for 2KD-FTV ) | ||
| Generator assembly (for 5L-E) | ||
| Combination meter assembly | ||
| Low engine oil pressure warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Oil Pressure] | ||
| Engine oil pressure switch assembly (for 1GD-FTV) | ||
| Engine oil pressure switch assembly (for 2GD-FTV) | ||
| Engine oil pressure switch assembly (for 1KD-FTV) | ||
| Engine oil pressure switch assembly (for 2KD-FTV) | ||
| Engine oil pressure switch assembly (for 2TR-FE) | ||
| Engine oil pressure switch assembly (for 1GR-FE) | ||
| Engine oil pressure switch assembly (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| A/T OIL TEMP warning light malfunction (for 4WD, Automatic Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Check indicator/warning light | ||
| Perform Active Test [A/T Oil Temperature Operation] | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| Combination meter assembly | ||
| Four-wheel drive indicator light (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. 4WD (Yellow)] | ||
| Perform Active Test [4WD Indicator (Green)] | ||
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| Low speed four-wheel drive indicator light (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. 4LO] | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| T-BELT indicator light malfunction (for KD Series Engine, 5L-E) | Check indicator/warning light | |
| Combination meter assembly | ||
| Rear differential lock indicator light (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Perform Active Test [Indicat. Rr DIFF LOCK] | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| MIL (Malfunction indicator lamp) malfunction | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Check indicator/warning light | ||
| Perform Active Test [Check Engine Indicator] | ||
| Proceed to "MIL Circuit" (for 1GD-FTV) | ||
| Proceed to "MIL Circuit" (for 1GD-FTV, w/ DPF) | ||
| Proceed to "MIL Circuit" (for 2GD-FTV) | ||
| Proceed to "MIL Circuit" (for 1KD-FTV) | ||
| Proceed to "MIL Circuit" (for 2KD-FTV) | ||
| Proceed to "MIL Circuit" (for 2TR-FE) | ||
| Proceed to "MIL Circuit" (for 1GR-FE) | ||
| Proceed to "MIL Circuit" (for 5L-E) | ||
| Combination meter assembly | ||
| Slip indicator light malfunction (w/ VSC) | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Slip] | ||
| Proceed to "Slip Indicator Light Remains ON" | ||
| Proceed to "Slip Indicator Light does not Come ON" | ||
| Combination meter assembly | ||
| VSC OFF indicator light malfunction (w/ VSC) | Check indicator/warning light | |
| Perform Active Test [Indicat. VSC OFF] | ||
| Proceed to "VSC OFF Switch Circuit" | ||
| Combination meter assembly | ||
| TRC OFF indicator light malfunction (w/ VSC) | Check indicator/warning light | |
| Perform Active Test [VSC TRC Indicator] | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| ABS warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp ABS] | ||
| Proceed to "ABS Warning Light Remains ON" (w/ VSC) | ||
| Proceed to "ABS Warning Light does not Come ON" (w/ VSC) | ||
| Proceed to "ABS Warning Light Remains ON" (w/o VSC) | ||
| Proceed to "ABS Warning Light does not Come ON" (w/o VSC) | ||
| Combination meter assembly | ||
| Downhill assist control system indicator light malfunction (w/ Downhill Assist Control) | Check indicator/warning light | |
| Perform Active Test [Indicat. Downhill Assist Control] | ||
| Proceed to "Downhill Assist Control Indicator Light Remains ON" | ||
| Proceed to "Downhill Assist Control Indicator Light does not Come ON" | ||
| Combination meter assembly | ||
| GLOW indicator light malfunction (for Diesel Engine) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. GLOW] | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| Fuel system warning light malfunction (for Diesel Engine) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Check indicator/warning light | ||
| Perform Active Test [Indicat. Fuel Filter Indicator] | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| ECD system (for 5L-E) | ||
| Fuel filter assembly (for 1GD-FTV) | ||
| Fuel filter assembly (for 2GD-FTV) | ||
| Fuel filter assembly (for 1KD-FTV) | ||
| Fuel filter assembly (for 2KD-FTV) | ||
| Fuel filter assembly (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| ECM (for 1GD-FTV) | ||
| ECM (for 2GD-FTV) | ||
| Low engine oil level warning light malfunction (Tachometer and engine coolant temperature receiver gauge are operate normally) (for GD Series Engine) | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Oil Level] | ||
| Engine oil level sensor (for 1GD-FTV) | ||
| Engine oil level sensor (for 2GD-FTV) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Speed warning light malfunction (Speedometer is operate normally) (for Middle East) | Check indicator/warning light | |
| Combination meter assembly | ||
| Oil maintenance warning light malfunction (w/ Oil Maintenance Required Reminder) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Check indicator/warning light | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| Combination meter assembly | ||
| LED headlight indicator light malfunction (for LED Headlight) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [LED Head Lamp Warning] | ||
| Lighting system | ||
| Combination meter assembly | ||
| Headlight leveling ECU assembly | ||
| Headlight leveling indicator light malfunction (for LED Headlight) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. Headlamp Auto Leveling] | ||
| Automatic headlight beam level control system | ||
| Combination meter assembly | ||
| Headlight leveling ECU assembly | ||
| DPF system warning light malfunction (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Check indicator/warning light | ||
| Perform Active Test [Diesel Particulate Filter Warning] | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| POWER MODE indicator light malfunction (for 1GD-FTV, w/ ECO MODE Indicator Light) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. Lamp ECT PWR] | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60E) | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) | ||
| Combination meter assembly | ||
| ECM (for 1GD-FTV) | ||
| POWER MODE indicator light malfunction (for 2GD-FTV, w/ ECO MODE Indicator Light) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. Lamp ECT PWR] | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60E) | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) | ||
| Combination meter assembly | ||
| ECM (for 2GD-FTV) | ||
| POWER MODE indicator light malfunction (for 2TR-FE, w/ ECO MODE Indicator Light) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. Lamp ECT PWR] | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60E) | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) | ||
| ECM (for 2TR-FE) | ||
| POWER MODE indicator light malfunction (for 1GR-FE, w/ ECO MODE Indicator Light) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. Lamp ECT PWR] | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" (for AC60F) | ||
| ECM (for 1GR-FE) | ||
| ECO MODE indicator light malfunction (w/ ECO MODE Indicator Light) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Perform Active Test [Indicat. ECO MODE] | ||
| Combination switch assembly (eco mode switch) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| ECM (for 1GD-FTV) | ||
| ECM (for 2GD-FTV) | ||
| ECM (for 2TR-FE) | ||
| ECM (for 1GR-FE) | ||
| iMT indicator light malfunction (for Intelligent Manual Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Check indicator/warning light | ||
| Perform Active Test [iMT Indicator (Green)] | ||
| Perform Active Test [iMT Indicator (Yellow)] | ||
| Proceed to "Pattern Select Switch iMT Mode Circuit" | ||
| Combination meter assembly | ||
| ECM (for 2GD-FTV) | ||
| ECM (for 2KD-FTV) | ||
| Eco driver indicator light malfunction (w/ Eco Drive Indicator Light) | Check customize setting | |
| CAN communication system (for LHD) | ||
| CAN communication system (for RHD) | ||
| Check indicator/warning light | ||
| Perform Active Test [Indicat. ECONO] | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECM (for 1GD-FTV) | ||
| ECM (for 2GD-FTV) | ||
| ECM (for 1KD-FTV) | ||
| ECM (for 2TR-FE) | ||
| ECM (for 1GR-FE) | ||
| Combination meter assembly | ||
| Open door warning light malfunction | Perform Active Test [Indicat. Lamp Doors All Open] | |
| Read the Data List [Driver Side Door, Passenger Side Door, Rear Left Side Door, Rear Right Side Door] | ||
| Harness or connector | - | |
| Front door courtesy switch assembly RH | ||
| Front door courtesy switch assembly LH | ||
| Rear door courtesy switch assembly RH | ||
| Rear door courtesy switch assembly LH | ||
| Back door lock assembly (back door courtesy switch) | ||
| Combination meter assembly | ||
| Master warning light malfunction (Other systems operate normally) | Check indicator/warning light | |
| Perform Active Test [Master Warning] | ||
| Combination meter assembly | ||
| Fuel level warning light malfunction (Fuel receiver gauge operates normally) | Perform Active Test [Indicat. Lamp Fuel] | |
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| "OPENING" display malfunction | Combination meter assembly | |
| "ENDING" display malfunction | Combination meter assembly | |
| "OTHER (BLANK)" display malfunction | Combination meter assembly | |
| "CURRENT FUEL CONSUMPTION" display malfunction (Combination meter assembly operates normally) (w/ Drive Monitor) | Combination meter assembly | |
| "AVERAGE FUEL CONSUMPTION (AFTER RESET)" display malfunction (Combination meter assembly operates normally) (w/ Drive Monitor) | Combination meter assembly | |
| "DISTANCE (RANGE)" display malfunction (Combination meter assembly operates normally) (w/ Drive Monitor) | Combination meter assembly | |
| "AVERAGE SPEED (AFTER RESET)" display malfunction (Combination meter assembly operates normally) (w/ Drive Monitor) | Combination meter assembly | |
| "ELAPSED TIME (AFTER RESET)" display malfunction (Combination meter assembly operates normally) (w/ Drive Monitor) | Combination meter assembly | |
| "DRIVE INFORMATION" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ECO DRIVING INDICATOR ZONE" display malfunction (w/ Eco Drive Indicator Light) | Check customize setting | |
| CAN communication system (for LHD) | ||
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECM (for 1GD-FTV) | ||
| ECM (for 2GD-FTV) | ||
| ECM (for 1KD-FTV) | ||
| ECM (for 2TR-FE) | ||
| ECM (for 1GR-FE) | ||
| Combination meter assembly | ||
| "SETTING" display malfunction | Combination meter assembly | |
| "ACCELERATOR AND BRAKE PEDALS DEPRESSED SIMULTANEOUSLY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "BRAKE OVERRIDE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "CHECK ENGINE REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "CHECK ENGINE VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "ENGINE MAINTENANCE REQUIRED VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "WATER ACCUMULATION IN FUEL FILTER SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Diesel Engine) | Fuel filter assembly (for 1GD-FTV) | |
| Fuel filter assembly (for 2GD-FTV) | ||
| Fuel filter assembly (for 1KD-FTV) | ||
| Fuel filter assembly (for 2KD-FTV) | ||
| Fuel filter assembly (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "REPLACE FUEL FILTER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Diesel Engine) | Harness or connector | - |
| Combination meter assembly | ||
| "ENGINE OIL LEVEL LOW ADD OR REPLACE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Tachometer and engine coolant temperature receiver gauge are operate normally) (for GD Series Engine) | Engine oil level sensor (for 1GD-FTV) | |
| Engine oil level sensor (for 2GD-FTV) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "HEADLIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Lighting system | ||
| Automatic headlight beam level control system (w/ Automatic Headlight Beam Level Control System) | ||
| Combination meter assembly | ||
| "2WD-4WD MODE CHANGE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| "DIFFERENTIAL OIL TEMP HIGH COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| "DIFFERENTIAL OIL TEMP HIGH SHIFT TO 2WD MODE COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| "TRC TURNED OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ VSC) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| "CRUISE CONTROL MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Cruise Control System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Cruise control system | ||
| Combination meter assembly | ||
| "iMT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Intelligent Manual Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Manual transmission system | ||
| Combination meter assembly | ||
| "TRANSMISSION FLUID TEMP HIGH SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Automatic transmission system (AC60F, for 1GR-FE) | ||
| Automatic transmission system (AC60F, for 1GD-FTV) | ||
| Automatic transmission system (AC60F, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 2TR-FE) | ||
| Combination meter assembly | ||
| "T-BELT MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "RESETTING T-BELT MAINTENANCE DATA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| T-BELT maintenance mileage message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "RESETTING OF T-BELT MAINTENANCE DATA NOW POSSIBLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "RESETTING OF T-BELT MAINTENANCE DATA COMPLETE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "OVER 120km/h" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Middle East) | Combination meter assembly | |
| "DPF FULL SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF FULL VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "MANUAL REGENERATION IN PROCESS KEEP FLAMMABLES AWAY FROM VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF REGENERATION IN PROCESS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF MANUAL REGENERATION AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF FULL MANUAL REGENERATION REQUIRED SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | |
| "ECO saving" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ECO score" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Current fuel consumption" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (Range)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Drive Information" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Eco driving indicator zone" display malfunction (w/ Eco Drive Indicator Light) | Check customize setting | |
| CAN communication system (for LHD) | ||
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| ECM (for 1GD-FTV) | ||
| ECM (for 2GD-FTV) | ||
| ECM (for 1KD-FTV) | ||
| ECM (for 2TR-FE) | ||
| ECM (for 1GR-FE) | ||
| ECM (for 5L-E) | ||
| Combination meter assembly | ||
| "Other (Blank)" display malfunction | Combination meter assembly | |
| "Outside temp" display malfunction | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Icy street warning" display malfunction | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Drive information tab" display malfunction | Combination meter assembly | |
| "Navigation tab" display malfunction (w/ Navigation System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Navigation system | ||
| Combination meter assembly | ||
| "Audio tab" display malfunction (w/ Audio and Visual System [for Radio and Display Type]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Navigation system (w/ Navigation System) | ||
| Audio and Visual System (for Radio and Display Type) | ||
| Combination meter assembly | ||
| "Cruise control operation guide tab" display malfunction (w/ Cruise Control System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Cruise control system | ||
| Combination meter assembly | ||
| "Message tab" display malfunction | Combination meter assembly | |
| "Setting tab" display malfunction | Combination meter assembly | |
| "Smart Entry & Start System malfunction See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Steering wheel lock Press engine switch while turning wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress brake and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key not detected Check key location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress brake and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | Click here | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key battery low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Turn off vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Shift to P before exiting vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Power turned off to save battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Push and hold engine switch for emergency stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Shift to N and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Automatic Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System [for Manual Transmission]) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key left inside vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "ACCESSORY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Low oil pressure Stop in a safe place See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil pressure switch assembly (for 1GD-FTV) | |
| Engine oil pressure switch assembly (for 2GD-FTV) | ||
| Engine oil pressure switch assembly (for 1KD-FTV) | ||
| Engine oil pressure switch assembly (for 2KD-FTV) | ||
| Engine oil pressure switch assembly (for 2TR-FE) | ||
| Engine oil pressure switch assembly (for 1GR-FE) | ||
| Engine oil pressure switch assembly (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "Engine oil level low Add or replace" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Tachometer and engine coolant temperature receiver gauge are operate normally) (for GD Series Engine) | Engine oil level sensor (for 1GD-FTV) | |
| Engine oil level sensor (for 2GD-FTV) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "Transmission fluid temp high See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Automatic transmission system (AC60F, for 1GR-FE) | ||
| Automatic transmission system (AC60F, for 1GD-FTV) | ||
| Automatic transmission system (AC60F, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 2TR-FE) | ||
| Combination meter assembly | ||
| "Transmission system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD, Automatic Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Automatic transmission system (AC60F, for 1GR-FE) | ||
| Automatic transmission system (AC60F, for 1GD-FTV) | ||
| Automatic transmission system (AC60F, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 2TR-FE) | ||
| Combination meter assembly | ||
| ECM (for 1GD-FTV) | ||
| "Cruise control malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Cruise Control System) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Cruise control system | ||
| Combination meter assembly | ||
| "iMT system malfunction visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Intelligent Manual Transmission) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Manual transmission system | ||
| Combination meter assembly | ||
| "Accelerator and brake pedals depressed simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Brake override malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Check Engine Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Check Engine Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Engine maintenance required Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| ECD system (for 2GD-FTV) | ||
| ECD system (for 1KD-FTV) | ||
| ECD system (for 2KD-FTV) | ||
| SFI system (for 2TR-FE) | ||
| SFI system (for 1GR-FE) | ||
| ECD system (for 5L-E) | ||
| Combination meter assembly | ||
| "Water accumulation in fuel filter See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Diesel Engine) | Level warning switch (for 1GD-FTV) | |
| Level warning switch (for 2GD-FTV) | ||
| Level warning switch (for 1KD-FTV) | ||
| Level warning switch (for 2KD-FTV) | ||
| Level warning switch (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "Replace fuel filter" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Diesel Engine) | Fuel filter assembly (clogging switch) (for 1KD-FTV) | |
| Fuel filter assembly (clogging switch) (for 2KD-FTV) | ||
| Fuel filter assembly (clogging switch) (for 1GD-FTV) | ||
| Fuel filter assembly (clogging switch) (for 2GD-FTV) | ||
| Fuel filter assembly (clogging switch) (for 5L-E) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "Headlight system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Lighting system | ||
| Automatic headlight beam level control system | ||
| Combination meter assembly | ||
| "2WD-4WD mode change malfunction visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| 4 wheel drive control ECU | ||
| "Differential oil temp high Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| "Differential oil temp high Shift to 2WD mode Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4WD) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| "TRC turned off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ VSC) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| "T-BELT maintenance required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "Resetting T-BELT maintenance data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "Resetting T-BELT maintenance data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| T-BELT maintenance mileage message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "Resetting of T-BELT maintenance data now possible" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "Resetting of T-BELT maintenance data complete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for KD Series Engine, 5L-E) | Combination meter assembly | |
| "Over 120km/h" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Middle East) | Combination meter assembly | |
| "DPF full See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF full Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "Manual regeneration in process Keep flammables away from vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF regeneration in process" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF manual regeneration available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly | ||
| "DPF full Manual regeneration required See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| All buzzers do not operate normally | Harness or connector | - |
| Combination meter assembly | ||
| Manual transmission reverse buzzer does not operate (for Manual Transmission [RC60/RC61]) | Harness or connector | - |
| Back-up light switch assembly (RC60/RC61) | ||
| Back-up light switch assembly (RC61F) | ||
| Combination meter assembly | ||
| Vehicle stability control sideways sliding warning buzzer does not operate (w/ VSC) | Vehicle stability control system | |
| Combination meter assembly | ||
| Temperature warning/CRAWL cancel warning buzzer does not operate (w/ VSC) | Vehicle stability control system | |
| Combination meter assembly | ||
| Brake system temperature rise/Active Test does not operate (w/ VSC) | Vehicle stability control system | |
| Combination meter assembly | ||
| Brake system low braking force warning buzzer does not operate (w/ VSC) | Vehicle stability control system | |
| Combination meter assembly | ||
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | Check customize setting | |
| Combination meter assembly | ||
| Brake fluid low warning buzzer does not operate (Speedometer and brake warning light are normal) | Combination meter assembly | |
| Engine oil pressure warning buzzer does not operate (Speedometer, tachometer and low engine oil pressure warning light are normal) | Combination meter assembly | |
| 4WD warning buzzer does not operate (for 4WD) | Touch select 2-4 and high-low system | |
| Combination meter assembly | ||
| 4 wheel drive control ECU | ||
| Front differential oil temperature warning buzzer does not operate (for 4WD) | Differential system (w/ Differential Lock) | |
| Combination meter assembly | ||
| Door open while not in P warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Smart entry and start system warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Engine switch operation while driving warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Restart while driving notification buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Immobiliser certification buzzer does not operate (w/ Immobiliser System) | Immobiliser system (w/ Smart Entry and Start System) | |
| Immobiliser system (w/o Smart Entry and Start System) | ||
| Combination meter assembly | ||
| Key reminder buzzer does not operate (w/o Smart Entry and Start System) | Key reminder warning system | |
| PKB-ON driving warning buzzer does not operate (Speedometer and parking brake warning light are operate normally) | Combination meter assembly | |
| Driving with door ajar warning buzzer does not operate (Open door warning light and speedometer operate normally) | Combination meter assembly | |
| Fuel system warning buzzer does not operate (Fuel system warning light normally) (for Diesel Engine) | Combination meter assembly | |
| Sports shift reject buzzer does not operate (for Automatic Transmission) | Automatic transmission system (A750F) | |
| Automatic transmission system (AC60E, for 1GD-FTV) | ||
| Automatic transmission system (AC60E, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 1GR-FE) | Click here | |
| Automatic transmission system (AC60F, for 1GD-FTV) | ||
| Automatic transmission system (AC60F, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 2TR-FE) | ||
| Combination meter assembly | ||
| Light reminder warning buzzer does not operate (Open door warning light and taillight indicator light operate normally) | Combination meter assembly | |
| MIL (Malfunction indicator lamp) buzzer does not operate (MIL [Malfunction indicator lamp] operate normally) | Combination meter assembly | |
| Turn signal flasher buzzer does not operate (Turn indicator light normally) | Combination meter assembly | |
| Multi-information display warning buzzer does not operate | Combination meter assembly | |
| Speed limit exceeded buzzer does not operate (Speedometer is operate normally) (for Middle East) | Combination meter assembly | |
| DPF buzzer does not operate (w/ DPF) | CAN communication system (for LHD) | |
| CAN communication system (for RHD) | ||
| ECD system (for 1GD-FTV, w/ DPF) | ||
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| DTCs display malfunction (Other systems operate normally) | Combination meter assembly | |
| "ODO/TRIP meter" display malfunction | Combination meter assembly | |
| Multi-information display does not change using steering pad switch assembly | Read the Data List [Multi Switch (UP), Multi Switch (Down), Multi Switch (Menu), Multi Switch (ENTER), Multi Switch (Right), Multi Switch (Left) or Multi Switch (Back)] (for TFT Display Type) | |
| Read the Data List [Multi Display Select Switch or Multi Switch (Back)] (for Dot Display Type) | ||
| Steering pad switch assembly | ||
| Spiral with sensor cable sub-assembly | ||
| Combination meter assembly | ||
| ODO/TRIP meter display does not change using trip switch | Combination meter assembly | |
| Shift Indicator display malfunction (for Automatic Transmission) | Perform Active Test [A/T Indicator Operation 1] | |
| Perform Active Test [A/T Indicator Operation 2] | ||
| Perform Active Test [A/T Indicator Operation 3] | ||
| Automatic transmission system (A750F) | ||
| Automatic transmission system (AC60E, for 1GD-FTV) | ||
| Automatic transmission system (AC60E, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 1GR-FE) | Click here | |
| Automatic transmission system (AC60F, for 1GD-FTV) | ||
| Automatic transmission system (AC60F, for 2GD-FTV) | ||
| Automatic transmission system (AC60F, for 2TR-FE) | ||
| Combination meter assembly | ||
| Meter illumination is always dark (Taillight operates normally) | Harness or connector | - |
| Combination meter assembly | ||
| Meter illumination does not dim at night (Taillight operates normally) | Harness or connector | - |
| Combination meter assembly | ||
| Operating light control rheostat does not change light brightness | Combination meter assembly | |
| Other systems that use the speed signal do not operate normally | Proceed to "Speed signal Circuit" |