Note
When replacing the combination meter assembly, make sure to replace it with a new one.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.
Click here
w/ Navigation System:
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.
w/ Audio and Visual System (for Radio and Display Type):
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.
Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | Link |
|---|---|---|
| Speedometer malfunction | Refer to "Speedometer Malfunction" | |
| Tachometer malfunction | Refer to "Tachometer Malfunction" | |
| Fuel receiver gauge malfunction (Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past) |
Refer to "Fuel Receiver Gauge Display Malfunction" | |
| Engine coolant temperature receiver gauge malfunction | Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" |
| Symptom | Suspected Area | Link |
|---|---|---|
| Turn indicator light malfunction (Turn signal light operates normally) | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | |
| Proceed to "Turn Signal Switch Circuit" | ||
| Proceed to "Hazard Warning Switch Circuit" | ||
| Combination meter assembly | ||
| Front fog indicator light malfunction (Front fog light operates normally) | Perform Active Test [Indicat. Lamp Fr FOG] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| Taillight indicator light malfunction (Taillight operates normally) | Perform Active Test [Indicat. Lamp Tail] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| High beam indicator light malfunction (High beam headlight operates normally) | Perform Active Test [Indicat. Lamp Beam] | |
| Harness or connector | - | |
| Combination meter assembly | ||
| Smart entry and start system indicator light malfunction | CAN communication system | |
| Perform Active Test [Smart System Indicator] | ||
| Perform Active Test [Smart System Warning] | ||
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Cruise indicator light malfunction | CAN communication system | |
| Proceed to "Cruise Main Indicator Light Circuit" | ||
| Combination meter assembly | ||
| SET indicator light malfunction | CAN communication system | |
| Proceed to "Cruise SET Indicator Light Circuit" | ||
| Combination meter assembly | ||
| Brake override system warning light malfunction | CAN communication system | |
| Check indicator/warning light | ||
| Perform Active Test [Brake Override Indicator] | ||
| ECD system | ||
| Combination meter assembly | ||
| Seat belt warning light malfunction | Proceed to "Driver Side Seat Belt Warning Light does not Operate" | |
| Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" | ||
| Parking brake warning light malfunction | Perform Active Test [Indicat. Park] | |
| Parking brake switch assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Brake warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Brake] | ||
| Proceed to "Brake Warning Light Remains ON" | ||
| Proceed to "Brake Warning Light does not Come ON" | ||
| Harness or connector | - | |
| Brake master cylinder sub-assembly (brake fluid level warning switch) | ||
| Vacuum warning switch assembly | ||
| Combination meter assembly | ||
| SRS warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Airbag] | ||
| Proceed to "SRS Warning Light Remains ON" | ||
| Proceed to "SRS Warning Light does not Come ON" | ||
| Combination meter assembly | ||
| Charger system warning light malfunction | CAN communication system | |
| Perform Active Test [Indicat. Lamp Charge] | ||
| Charging system | ||
| Combination meter assembly | ||
| Low engine oil pressure warning light malfunction | Perform Active Test [Indicat. Oil Pressure] | |
| Engine oil pressure switch assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| A/T OIL TEMP warning light malfunction (for Automatic Transmission) | CAN communication system | |
| Check indicator/warning light | ||
| Perform Active Test [A/T Oil Temperature Operation] | ||
| ECD system | ||
| Combination meter assembly | ||
| Four-wheel drive indicator light | CAN communication system | |
| Perform Active Test [Indicat. 4WD (Yellow)] | ||
| Perform Active Test [4WD Indicator (Green)] | ||
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| Low speed four-wheel drive indicator light | CAN communication system | |
| Perform Active Test [Indicat. 4LO] | ||
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| Rear differential lock indicator light (for 4WD) | CAN communication system | |
| Perform Active Test [Indicat. Rr DIFF LOCK] | ||
| Differential system (w/ Differential Lock) | ||
| Combination meter assembly | ||
| MIL (Malfunction Indicator Lamp) malfunction | CAN communication system | |
| Check indicator/warning light | ||
| Perform Active Test [Check Engine Indicator] | ||
| Proceed to "MIL Circuit" | ||
| Combination meter assembly | ||
| Slip indicator light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Slip] | ||
| Proceed to "Slip Indicator Light Remains ON" | ||
| Proceed to "Slip Indicator Light does not Come ON" | ||
| Combination meter assembly | ||
| VSC indicator light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. VSC OFF] | ||
| Proceed to "VSC OFF Switch Circuit" | ||
| Combination meter assembly | ||
| TRC OFF indicator light malfunction | CAN communication system | |
| Check indicator/warning light | ||
| Perform Active Test [VSC OFF Indicator] | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| ABS warning light malfunction | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp ABS] | ||
| Proceed to "ABS Warning Light Remains ON" | ||
| Proceed to "ABS Warning Light does not Come ON" | ||
| Combination meter assembly | ||
| Downhill assist control system indicator light malfunction (w/ Downhill Assist Control) | Check indicator/warning light | |
| Perform Active Test [Indicat. Downhill Assist Control] | ||
| Proceed to "Downhill Assist Control Indicator Light Remains ON" | ||
| Proceed to "Downhill Assist Control Indicator Light does not Come ON" | ||
| Combination meter assembly | ||
| GLOW indicator light malfunction | CAN communication system | |
| Perform Active Test [Indicat. GLOW] | ||
| ECD system | ||
| Combination meter assembly | ||
| Fuel system warning light malfunction | CAN communication system | |
| Check indicator/warning light | ||
| Perform Active Test [Indicat. Fuel Filter Indicator] | ||
| ECD system | ||
| Level warning switch | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Low engine oil level warning light malfunction (Tachometer and engine coolant temperature receiver gauge operate normally) | Check indicator/warning light | |
| Perform Active Test [Indicat. Lamp Oil Level] | ||
| Engine oil level sensor | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| LED headlight indicator light malfunction (for LED Headlight) | CAN communication system | |
| Perform Active Test [LED Head Lamp Warning] | ||
| Lighting system | ||
| Combination meter assembly | ||
| Headlight leveling indicator light malfunction (for LED Headlight) | CAN communication system | |
| Perform Active Test [Indicat. Headlamp Auto Leveling] | ||
| Automatic headlight beam level control system | ||
| Combination meter assembly | ||
| POWER MODE indicator light malfunction (w/ ECO MODE Indicator Light) | CAN communication system | |
| Perform Active Test [Indicat. Lamp ECT PWR] | ||
| Proceed to "Pattern Select Switch Power Mode Circuit" | ||
| Combination meter assembly | ||
| ECM | ||
| ECO MODE indicator light malfunction (w/ ECO MODE Indicator Light) | CAN communication system | |
| Perform Active Test [Indicat. ECO MODE] | ||
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| Eco driver indicator light malfunction | Check customize setting | |
| CAN communication system | ||
| Check indicator/warning light | ||
| Perform Active Test [Indicat. ECONO] | ||
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| Open door warning light malfunction | Perform Active Test [Indicat. Lamp Doors All Open] | |
| Read the Data List [Driver Side Door, Passenger Side Door, Rear Left Side Door, Rear Right Side Door] | ||
| Front door courtesy switch assembly RH | ||
| Front door courtesy switch assembly LH | ||
| Rear door courtesy switch assembly RH | ||
| Rear door courtesy switch assembly LH | ||
| Back door lock assembly (back door courtesy switch) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Master warning light malfunction (Other systems operate normally) | Check indicator/warning light | |
| Perform Active Test [Master Warning] | ||
| Combination meter assembly | ||
| Fuel level warning light malfunction (Fuel receiver gauge operates normally) | Perform Active Test [Indicat. Lamp Fuel] | |
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | |
| "ECO wallet" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ECO score" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Current fuel consumption" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (Range)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Eco driving indicator zone" display malfunction | Check customize setting | |
| CAN communication system | ||
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "Other (Blank)" display malfunction | Combination meter assembly | |
| "Outside temp" display malfunction | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Icy street warning" display malfunction | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Drive information tab" display malfunction | Combination meter assembly | |
| "Navigation tab" display malfunction (w/ Navigation System) | CAN communication system | |
| Navigation system | ||
| Combination meter assembly | ||
| "Audio tab" display malfunction (w/ Audio and Visual System [for Radio and Display Type]) | CAN communication system | |
| Audio and visual system (for Radio and Display Type) | ||
| Navigation system (w/ Navigation System) | ||
| Combination meter assembly | ||
| "Cruise control operation guide tab" display malfunction | CAN communication system | |
| Cruise control system | ||
| Combination meter assembly | ||
| "Message tab" display malfunction | Combination meter assembly | |
| "Setting tab" display malfunction | Combination meter assembly | |
| "Smart Entry & Start System malfunction See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Steering wheel lock Press engine switch while turning wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress brake and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and then touch key to engine switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key not detected Check key location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress brake and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and then start engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key battery low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Turn off vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Shift to P before exiting vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Power turned off to save battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Push and hold engine switch for emergency stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Shift to N and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Depress clutch and press engine switch to restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Key left inside vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "ACCESSORY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "Low oil pressure Stop in a safe place See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil pressure switch assembly | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Engine oil level low Add or replace" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Tachometer and engine coolant temperature receiver gauge operate normally) | Engine oil level sensor | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Transmission fluid temp high See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission) | CAN communication system | |
| Automatic transmission system | ||
| Combination meter assembly | ||
| ECM | ||
| "Transmission system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission) | CAN communication system | |
| Automatic transmission system | ||
| Combination meter assembly | ||
| ECM | ||
| "Cruise control malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Cruise control system | ||
| Combination meter assembly | ||
| "Accelerator and brake pedals depressed simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Brake override malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Check Engine Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Check Engine Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Reduced engine power Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Engine maintenance required Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Replace fuel filter" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| "Water accumulation in fuel filter See owner's manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Level warning switch | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Headlight system malfunction Visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) | CAN communication system | |
| Lighting system | ||
| Automatic headlight beam level control system | ||
| Combination meter assembly | ||
| "2WD-4WD mode change malfunction visit your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| "Differential oil temp high Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| "Differential oil temp high Shift to 2WD mode Cooling time required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| "TRC turned off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Vehicle stability control system | ||
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| "OPENING" display malfunction | Combination meter assembly | |
| "ENDING" display malfunction | Combination meter assembly | |
| "OTHER (BLANK)" display malfunction | Combination meter assembly | |
| "CURRENT FUEL CONSUMPTION" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "AVERAGE FUEL CONSUMPTION (AFTER RESET)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "DISTANCE (RANGE)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "AVERAGE SPEED (AFTER RESET)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ELAPSED TIME (AFTER RESET)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "DRIVE INFORMATION" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ECO DRIVING INDICATOR ZONE" display malfunction | Check customize setting | |
| CAN communication system | ||
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "SETTING" display malfunction | Combination meter assembly | |
| "OUTSIDE TEMP" display malfunction (for Automatic Air Conditioning System) | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "ICY STREET WARNING" display malfunction (for Automatic Air Conditioning System) | Thermistor assembly (ambient temperature sensor) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "ACCELERATOR AND BRAKE PEDALS DEPRESSED SIMULTANEOUSLY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "BRAKE OVERRIDE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "CHECK ENGINE REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "CHECK ENGINE VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "REDUCED ENGINE POWER VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "ENGINE MAINTENANCE REQUIRED VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "REPLACE FUEL FILTER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Combination meter assembly | ||
| ECM | ||
| "WATER ACCUMULATION IN FUEL FILTER SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Harness or connector | - |
| Level warning switch assembly | ||
| Combination meter assembly | ||
| "ENGINE OIL LEVEL LOW ADD OR REPLACE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| ECD system | ||
| Engine oil pressure switch assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| ECM | ||
| "2WD-4WD MODE CHANGE MALFUNCTION VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Touch select 2-4 and high-low system | ||
| Combination meter assembly | ||
| 4 wheel drive control ECU | ||
| "DIFFERENTIAL OIL TEMP HIGH COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Differential system | ||
| Combination meter assembly | ||
| 4 wheel drive control ECU | ||
| "DIFFERENTIAL OIL TEMP HIGH SHIFT TO 2WD MODE COOLING TIME REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Differential system | ||
| Combination meter assembly | ||
| 4 wheel drive control ECU | ||
| "TRC TURNED OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | |
| Vehicle stability control system | ||
| Combination meter assembly | ||
| Brake actuator assembly (skid control ECU) | ||
| "SMART ENTRY & START SYSTEM MALFUNCTION SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "STEERING WHEEL LOCK PRESS ENGINE SWITCH WHILE TURNING WHEEL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS BRAKE AND THEN TOUCH KEY TO ENGINE SWITCH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS CLUTCH AND THEN TOUCH KEY TO ENGINE SWITCH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "KEY NOT DETECTED CHECK KEY LOCATION" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS BRAKE AND THEN START ENGINE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS CLUTCH AND THEN START ENGINE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "TURN OFF VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "SHIFT TO P BEFORE EXITING VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "POWER TURNED OFF TO SAVE BATTERY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "PUSH AND HOLD ENGINE SWITCH FOR EMERGENCY STOP "message is displayed when it should not be, not displayed when it should be, or not displayed correctly EMERGENCY STOP (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "SHIFT TO N AND PRESS ENGINE SWITCH TO RESTART" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS CLUTCH AND PRESS ENGINE SWITCH TO RESTART" message is displayed when it should not be, not displayed when it should be, or not displayed correctly(for Manual Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "KEY LEFT INSIDE VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "DEPRESS BRAKE AND THEN START ENGINE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission with Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "ACCESSORY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly(w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| "IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Smart Entry and Start System) | CAN communication system | |
| Smart entry and start system (for Entry Function) | ||
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| All buzzers do not operate normally | Harness or connector | - |
| Combination meter assembly | ||
| Manual transmission reverse buzzer does not operate (for Manual Transmission) | Harness or connector | - |
| Back-up light switch assembly | ||
| Combination meter assembly | ||
| Vehicle stability control sideways sliding warning buzzer does not operate | Vehicle stability control system | |
| Combination meter assembly | ||
| Temperature warning/CRAWL cancel warning buzzer does not operate | Vehicle stability control system | |
| Combination meter assembly | ||
| Brake system temperature rise/Active Test does not operate | Vehicle stability control system | |
| Combination meter assembly | ||
| Brake system low braking force warning buzzer does not operate | Vehicle stability control system | |
| Combination meter assembly | ||
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | Check customize setting | |
| Combination meter assembly | ||
| Brake fluid low warning buzzer does not operate (Speedometer and brake warning light are normal) | Combination meter assembly | |
| Engine oil pressure warning buzzer does not operate (Speedometer, tachometer and low engine oil pressure warning light are normal) | Combination meter assembly | |
| 4WD warning buzzer does not operate | Touch select 2-4 and high-low system | |
| Combination meter assembly | ||
| Front differential oil temperature warning buzzer does not operate | Touch select 2-4 and high-low system | |
| Combination meter assembly | ||
| Door open while not in P warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Smart entry and start system warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Engine switch operation while driving warning buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Restart while driving notification buzzer does not operate (w/ Smart Entry and Start System) | Smart entry and start system (for Entry Function) | |
| Smart entry and start system (for Start Function) | ||
| Combination meter assembly | ||
| Immobiliser certification buzzer does not operate | Immobiliser system (w/ Smart Entry and Start System) | |
| Immobiliser system (w/o Smart Entry and Start System) | ||
| Combination meter assembly | ||
| PKB-ON driving warning buzzer does not operate (Speedometer and parking brake warning light are operate normally) | Combination meter assembly | |
| Driving with door ajar warning buzzer does not operate (Open door warning light and speedometer operate normally) | Combination meter assembly | |
| Fuel system warning buzzer does not operate (Fuel system warning light normally) | Combination meter assembly | |
| Sports shift reject buzzer does not operate (for Automatic Transmission) | ECD system | |
| Combination meter assembly | ||
| Light reminder warning buzzer does not operate (Open door warning light and taillight indicator light operate normally) | Combination meter assembly | |
| MIL (Malfunction Indicator Lamp) buzzer does not operate (MIL [Malfunction Indicator Lamp] operate normally) | Combination meter assembly | |
| Turn signal flasher buzzer does not operate (Turn indicator light normally) | Combination meter assembly | |
| Multi-information display warning buzzer does not operate | Combination meter assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| DTCs display malfunction (Other systems operate normally) | Combination meter assembly | |
| "ODO/TRIP meter" display malfunction | Combination meter assembly | |
| Multi-information display does not change using steering pad switch assembly | Read the Data List [Multi Switch (UP), Multi Switch (Down), Multi Switch (Menu), Multi Switch (ENTER, Multi Switch (Right) or Multi Switch (Left)] | |
| Steering pad switch assembly | ||
| Spiral with sensor cable sub-assembly | ||
| Combination meter assembly | ||
| ODO/TRIP meter display does not change using trip switch | Combination meter assembly | |
| Shift Indicator display malfunction (for Automatic Transmission) | Perform Active Test [A/T Indicator Operation 1] | |
| Perform Active Test [A/T Indicator Operation 2] | ||
| Perform Active Test [A/T Indicator Operation 3] | ||
| CAN communication system | ||
| Automatic transmission system | ||
| Combination meter assembly | ||
| Meter illumination is always dark (Taillight is normally) | Harness or connector | - |
| Combination meter assembly | ||
| Meter illumination does not dim at night (Taillight is normally) | Harness or connector | - |
| Combination meter assembly | ||
| Operating light control rheostat does not change light brightness | Combination meter assembly | |
| Other systems that use the speed signal do not operate normally | Proceed to "Speed signal Circuit" |