METER / GAUGE SYSTEM OPERATION CHECK

CHECK INDICATOR/WARNING LIGHT

1. Check the following indicators and warning lights.

   Indicator/Warning Light	Switch Condition	Specified Condition
   Brake override system warning light	Ignition switch off → ON	Comes on for 3 seconds
   Brake warning light
   Slip indicator light (w/ VSC)
   VSC indicator light (w/ VSC)
   TRC OFF indicator light (w/ VSC)
   ABS warning light
   Fuel system warning light (for Deisel Engine)
   Downhill assist control system indicator light (w/ Downhill Assist Control)
   iMT indicator light (for Intelligent Manual Transmission)
   Eco driver indicator light (w/ Eco Drive Indicator Light)
   T-BELT indicator light (for KD Series Engine)
   DPF warning light (w/ DPF)
   Tire pressure warning light (w/ Tire Pressure Warning System)
   SRS warning light	Ignition switch off → ON	Comes on for 6 seconds
   Low engine oil pressure warning light	Ignition switch off → ON	Turns off when engine started
   A/T OIL TEMP warning light (for 4WD, Automatic Transmission)
   MIL (Malfunction Indicator Lamp)
   Low engine oil level warning light (for GD Engine Series Engine)

CHECK SPEEDOMETER

1. Connect the GTS to the DLC3.

2. Turn the ignition switch to ON.

3. Turn the GTS on.

4. Enter the following menus: Powertrain / ABS/VSC/TRC / Data List.

   
   Chassis > ABS/VSC/TRC > Data List

   Tester Display	Measurement Item	Normal Condition	Reference Value	Diagnostic Note
   Vehicle Speed	Vehicle speed	Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)	Almost same as actual vehicle speed	-

   
   Chassis > ABS/VSC/TRC > Data List

   Tester Display
   Vehicle Speed

   for Australia (for TFT Display Type):

   Standard Indication (km/h)	Acceptable Range (km/h)
   20	20.5 to 24.5
   40	40.9 to 45.4
   60	61.4 to 65.9
   80	81.9 to 86.9
   100	102.4 to 105.9
   120	122.8 to 127.8
   140	143.3 to 148.3
   160	163.8 to 168.8
   180	184.3 to 189.3

   for Australia (for Dot Display Type):

   Standard Indication (km/h)	Acceptable Range (km/h)
   20	20.2 to 24.2
   40	40.5 to 45.0
   60	60.7 to 65.2
   80	81.0 to 86.0
   100	101.2 to 105.2
   120	121.4 to 126.4
   140	141.7 to 146.7
   160	161.9 to 166.9
   180	182.2 to 187.2

   except Australia:

   Standard Indication (km/h)	Acceptable Range (km/h)
   20	21 to 25
   40	41.7 to 46.2
   60	62.7 to 67.2
   80	83.4 to 88.4
   100	104.3 to 109.3
   120	125.1 to 130.6
   140	145.8 to 151.8
   160	166.2 to 173.2
   180	186.9 to 194.5

   If the result is not as specified, the speedometer may have a malfunction.

   Note

   Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

5. Check the deflection width of the speedometer indicator.

   CHECK TACHOMETER

   
   

   1. Connect a tune-up tachometer and start the engine.

   2. Compare the test results with the tachometer indicator.

   DC 13.5 V at 25°C (77°F)

   Standard Indication (rpm)	Acceptable Range Data in ( ) is for Reference (rpm)
   700	630 to 770
   1000	(900 to 1100)
   2000	(1850 to 2150)
   3000	2800 to 3200
   4000	(3800 to 4200)
   5000	4800 to 5200