IMMOBILISER SYSTEM(w/ Smart Entry and Start System) TERMINALS OF ECU


  1. CHECK ENGINE SWITCH

    B003KP2N43

    1. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G45-6 (AGND) - Body ground - SB - Body ground Transponder key amplifier ground Always Below 1 Ω -
      G45-7 (TXCT) - G45-6 (AGND) Input R - SB Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
      G45-8 (CODE) - G45-6 (AGND) Output Y - SB Immobiliser communication output Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
      G45-10 (VC5) - G45-6 (AGND) Input LG - SB Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -

      • *1: for Automatic Transmission

      • *2: for Manual Transmission

    2. Check for pulses according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G45-7 (TXCT) - G45-6 (AGND) Input R - SB

      Signal input from certification ECU (smart key ECU assembly)

      (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)

      		 Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

      Pulse generation

      (See waveform 1)

      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response

        Tech Tips

        If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above
      G45-8 (CODE) - G45-6 (AGND) Output Y - SB

      Signal output to certification ECU (smart key ECU assembly)

      (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly).)

      		 Engine switch off, engine switch pressed with key held near engine switch*

      Pulse generation

      (See waveform 2)
      G45-10 (VC5) - G45-6 (AGND) Input LG - SB

      Transponder key amplifier power supply

      (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)

      		 Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

      Pulse generation

      (See waveform 3)

      Tech Tips

      *: Remove the key battery before performing this inspection.

    3. Using an oscilloscope, check the waveform.

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B003JK5N18

        Waveform 1 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G45-7 (TXCT) - G45-6 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
      2. B003KVPC18
        *a Key held near engine switch

        Waveform 2 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G45-8 (CODE) - G45-6 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Engine switch off, engine switch pressed with key held near engine switch*

        Tech Tips

        *: Remove the key battery before performing this inspection.

      3. B003KLON05

        Waveform 3 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G45-10 (VC5) - G45-6 (AGND)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

  2. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B003JL4E01

    1. Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G16-1 (+B) - G16-10 (E) Input P - BR +B power supply Always 11 to 14 V -
      G17-33 (CUTB) - G16-10 (E) Input W - BR Stand-by power Always 11 to 14 V -
      G16-10 (E) - Body ground - BR - Body ground Ground Always Below 1 Ω -

    3. Reconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.

    4. Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G16-15 (IND) - G16-10 (E) Output Y - BR Security indicator light output Engine switch off → on (IG)

      Pulse generation

      → Below 2 V

      		 -
      G17-2 (TXCT) - G16-24 (AGND) Output R - SB Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V

      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response
      G17-1 (CODE) - G16-24 (AGND) Input Y - SB Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
      G17-20 (VC5) - G16-24 (AGND) Output LG - SB Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
      G16-24 (AGND) - Body ground - SB - Body ground Transponder key amplifier ground Always Below 1 Ω

      • *1: for Automatic Transmission

      • *2: for Manual Transmission

    5. Measure the voltage and check for pulses according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G17-2 (TXCT) - G16-24 (AGND) Output R - SB

      Signal output to transponder key amplifier

      (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)

      		 Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

      Pulse generation

      (See waveform 1)

      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response
      G17-1 (CODE) - G16-24 (AGND) Input Y - SB

      Signal input from transponder key amplifier

      (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly).)

      		 Engine switch off, engine switch pressed with key held near engine switch*1

      Pulse generation

      (See waveform 2)
      G17-20 (VC5) - G16-24 (AGND) Output LG - SB

      Transponder key amplifier power supply

      (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)

      		 Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

      Pulse generation

      (See waveform 3)
      G16-3 (EFII) - G16-24 (AGND)*2 Input Y - SB

      EFI communication input

      (Signal input from ECM to certification ECU (smart key ECU assembly))

      		 Engine switch off 11 to 14 V

      • B2799

      • B279A

      • Engine Start Request

      • EFI Code Receive
      G16-3 (EFII) - G16-24 (AGND)*2 Input Y - SB

      EFI communication input

      (Signal input from ECM to certification ECU (smart key ECU assembly))

      		 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 4)
      G17-35 (EFIO) - G16-24 (AGND)*2 Output B - SB

      EFI communication output

      (Signal output from certification ECU (smart key ECU assembly) to ECM)

      		 Engine switch off Below 1 V
      G17-35 (EFIO) - G16-24 (AGND)*2 Output B - SB

      EFI communication output

      (Signal output from certification ECU (smart key ECU assembly) to ECM)

      		 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 5)

      Tech Tips

      *1: Remove the key battery before performing this inspection.


      • *2: w/o ID Code Box (Immobiliser Code ECU)

    6. Using an oscilloscope, check the waveform.

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B003JK5N19

        Waveform 1 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G17-2 (TXCT) - G16-24 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
      2. B003KVPC18
        *a Key held near engine switch

        Waveform 2 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G17-1 (CODE) - G16-24 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Engine switch off, engine switch pressed with key held near engine switch*

        Tech Tips

        *: Remove the key battery before performing this inspection.

      3. B003KLON06

        Waveform 3 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G17-20 (VC5) - G16-24 (AGND)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

      4. Waveform 4 (Reference)

        B003OONC03
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G16-3 (EFII) - G16-24 (AGND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      5. Waveform 5 (Reference)

        B003O88C02
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G17-35 (EFIO) - G16-24 (AGND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

  3. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID Code Box [Immobiliser Code ECU])


    1. Disconnect the G138 ID code box (immobiliser code ECU) connector.

    2. B003S9FE07

      Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G138-1 (+B) - Body ground Input L - Body ground +B power supply Always 11 to 14 V B2789
      G138-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω B2789

      If the result is not as specified, there may be a malfunction on the wire harness side.

    3. Reconnect the G138 ID code box (immobiliser code ECU) connector.

    4. Measure the voltage and check the pulse according to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G138-3 (EFII) - G138-5 (GND) Input Y - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Engine switch off 11 to 14 V

      • B2799

      • B279A

      • Engine Start Request

      • EFI Code Receive
      G138-4 (EFIO) - G138-5 (GND) Output B - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Engine switch off Below 1 V
      G138-3 (EFII) - G138-5 (GND) Input Y - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation (See waveform 1)
      G138-4 (EFIO) - G138-5 (GND) Output B - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation (See waveform 2)

    5. Inspect using an oscilloscope.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1 (Reference)

        B003OONC03
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G138-3 (EFII) - G138-5 (GND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      2. Waveform 2 (Reference)

        B003O88C02
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G138-4 (EFIO) - G138-5 (GND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

  4. CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

    B003K5KN83

    1. Measure the voltage, resistance and check for pulses to the value(s) in the table below.

      Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
      G19-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      G19-3 (IGE) - G19-1 (GND) Input L - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly))

      Steering lock motor operates when both conditions met, and then door opened:


      • Shift lever in P*1

      • Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off

      Pulse generation

      (See waveform 1)

      • Power Supply Short

      • Unlock Request Receive

      • Lock Request Receive
      G19-4 (SLP1) - G19-1 (GND) Output R - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*2 11 to 14 V → Below 1.5 V

      • Push Start Error

      • Sensor Value
      G19-6 (IG2) - G19-1 (GND) Input P - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
      G19-7 (B) - Body ground Output W - Body ground Constant power supply Always 11 to 14 V B2788

      • *1: for Automatic Transmission

      If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.

      Tech Tips

      *2: The steering locks when any door is opened with the shift lever in P*1 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).

    2. Using an oscilloscope, check the waveform.

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B003SA1C03
        *a Steering lock motor not operating
        *b Steering lock motor operating

        Waveform 1 (Reference)

        Measurement Condition
        Item Content
        Tester Connection G19-3 (IGE) - G19-1 (GND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition

        Steering lock motor operates when both conditions met, and then door opened:


        • Shift lever in P*

        • Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off

        • *: for Automatic Transmission

  5. CHECK ECM (for 2TR-FE)

    B003K9FE05

    1. Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
      C146-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C146-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C146-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C147-5 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C146-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      G143-1 (+B) - C146-3 (E1) Input L - W-B IG power supply Engine switch on (IG) 11 to 14 V -
      G143-2 (+B2) - C146-3 (E1) Input B - W-B IG power supply Engine switch on (IG) 11 to 14 V -
      G143-3 (BATT) - C146-3 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
      G142-9 (IMO) - C146-3 (E1) Output Y - W-B

      Certification ECU (smart key ECU assembly) communication output*1

      ID code box (immobiliser code ECU) communication output*2

      		 Engine switch off 11 to 14 V E/G Start Permission
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      Pulse generation

      (See waveform 1)

      		 E/G Start Permission
      G142-10 (IMI) - C146-3 (E1) Input B - W-B

      Certification ECU (smart key ECU assembly) communication input*1

      ID code box (immobiliser code ECU) communication input*2

      		 Engine switch off Below 1 V E/G Start Permission
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      Pulse generation

      (See waveform 2)

      		 E/G Start Permission

      *1: w/o ID Code Box (Immobiliser Code ECU)

      *2: w/ ID Code Box (Immobiliser Code ECU)

    2. Using an oscilloscope, check the waveform.


      1. Waveform 1 (Reference)

        B003RG2C03
        *a Approximately 160 ms *b Approximately 270 ms
        Tester Connection G142-9 (IMO) - C146-3 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      2. Waveform 2 (Reference)

        B003O88C05
        *a Approximately 160 ms *b Approximately 270 ms
        Tester Connection G142-10 (IMI) - C146-3 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

  6. CHECK ECM (for 1GR-FE)

    B003JIQE28

    1. Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
      C83-12 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
      C83-29 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C83-23 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C82-16 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      C82-14 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
      G144-23 (+B) - C83-12 (E1) Input L - BR IG power supply Engine switch on (IG) 11 to 14 V -
      G144-22 (+B2) - C83-12 (E1) Input B - BR IG power supply Engine switch on (IG) 11 to 14 V -
      G144-24 (BATT) - C83-12 (E1) Input Y - BR +B power supply Always 11 to 14 V -
      G145-8 (IMO) - C83-12 (E1) Output Y - BR

      Certification ECU (smart key ECU assembly) communication output*1

      ID code box (immobiliser code ECU) communication output*2

      		 Engine switch off 11 to 14 V E/G Start Permission
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      Pulse generation

      (See waveform 1)

      		 E/G Start Permission
      G145-10 (IMI) - C83-12 (E1) Input B - BR

      Certification ECU (smart key ECU assembly) communication input*1

      ID code box (immobiliser code ECU) communication input*2

      		 Engine switch off Below 1 V E/G Start Permission
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      Pulse generation

      (See waveform 2)

      		 E/G Start Permission

      *1: w/o ID Code Box (Immobiliser Code ECU)

      *2: w/ ID Code Box (Immobiliser Code ECU)

    2. Using an oscilloscope, check the waveform.


      1. Waveform 1 (Reference)

        B003RG2C03
        *a Approximately 160 ms *b Approximately 270 ms
        Tester Connection G145-8 (IMO) - C83-12 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

      2. Waveform 2 (Reference)

        B003O88C05
        *a Approximately 160 ms *b Approximately 270 ms
        Tester Connection G145-10 (IMI) - C83-12 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

  7. CHECK ECM (for 1GD-FTV, 2GD-FTV)

    B003Q1QE01
    Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
    C41-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
    G50-1 (BATT) - C41-1 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
    G50-2 (+B) - C41-1 (E1) Input L - W-B +B power supply Engine switch on (IG) 11 to 14 V -
    G50-3 (+B2) - C41-1 (E1) Input B - W-B +B power supply Engine switch on (IG) 11 to 14 V -
    G50-17 (IMO) - C41-1 (E1) Output Y - W-B

    Certification ECU (smart key ECU assembly) communication output*1

    ID code box (immobiliser code ECU) communication output*2

    		 Engine switch off 11 to 14 V -
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    Pulse generation

    (See waveform 1)

    		 -
    G50-16 (IMI) - C41-1 (E1) Input B - W-B

    Certification ECU (smart key ECU assembly) communication input*1

    ID code box (immobiliser code ECU) communication input*2

    		 Engine switch off Below 1 V -
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    Pulse generation

    (See waveform 2)

    		 -

    *1: w/o ID Code Box (Immobiliser Code ECU)

    *2: w/ ID Code Box (Immobiliser Code ECU)


    1. Using an oscilloscope, check the waveform.

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1 (Reference)

        B003OONC03
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G50-17 (IMO) - C41-1 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      2. Waveform 2 (Reference)

        B003O88C02
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection G50-16 (IMI) - C41-1 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected