SMART ENTRY AND START SYSTEM(for Entry Function) OPERATION CHECK


  1. CHECK SMART ENTRY AND START SYSTEM (for Entry Function) OPERATION

    Note

    Make sure that the smart entry and start system (for Entry Function) has not been canceled before performing this inspection.


    1. Check the entry unlock function (for Driver Door).


      1. B003NNGC01
        *a Trigger Switch

        Perform a wireless lock operation to lock the door, press the trigger switch on the front door outside handle assembly (for Driver Door) of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.

        Tech Tips

        To perform a wireless lock operation, press the lock button of the electrical key transmitter sub-assembly while standing near the front door outside handle assembly (for Driver Door).

      2. B003QJRC01
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for Driver Door) at a distance of approximately 0.7 m (2.30 ft.), press the trigger switch, and check that all doors unlock.

        Tech Tips

        Inspect the front passenger door using the same procedure.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly (for Driver Door).

        • Inspect the front passenger door using the same procedure.

    2. Check the entry lock function (for Driver Door).

      Note

      If the electrical key transmitter sub-assembly is inside the vehicle but outside the detection area (on the instrument panel, on the floor, inside the door pocket or in the glove box) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle. To prevent key lock-in, perform the inspection with one of the door windows open.


      1. B003NNGC01
        *a Trigger Switch

        With the door closed and unlocked, press the trigger switch on the front door outside handle assembly (for Driver Door) of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.

      2. B003QJRC01
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for Driver Door) at a distance of approximately 0.7 m (2.30 ft.), press the trigger switch, and check that all doors lock.

        Tech Tips


        • If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna may be leaking from the vehicle.

        • Inspect the front passenger door using the same procedure.

    3. Check the entry back door open function.


      1. B003KJIC01
        *1 Back Door Opener Switch Assembly (Open Switch)
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Perform a wireless lock operation to lock the doors, operate the open switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly and check that the back door opens.

      2. Inspect the entry back door open operating range. Hold the electrical key transmitter sub-assembly at the same height as the back door opener switch assembly and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the open switch of the back door opener switch assembly and check that the back door opens.

    4. Check the entry back door lock function.

      Note

      If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box or on the floor) and a back door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


      1. With the back door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door locks.

      2. B003P8DC01
        *1 Back Door Opener Switch Assembly (Lock Switch)
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the back door opener switch assembly and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the lock switch of the back door opener switch assembly and check that the back door locks.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the back door opener switch assembly.

        • If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.

    5. Check the key lock-in prevention function (vehicle interior).

      Note

      In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.


      1. Turn the engine switch off.

      2. Place the electrical key transmitter sub-assembly on a front or rear seat.

      3. Close the door, making sure the doors are unlocked.

      4. Press the trigger switch on the front door outside handle assembly (for Driver Door) and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.

    6. Check the push start function. (for Automatic Transmission)


      1. With the engine switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly and check that the smart warning light in the combination meter assembly illuminates green. Then, when the smart warning light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.

      2. With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off. However, if the shift lever is in any position other than P while the engine switch is on (IG), the power source mode will not change to off, but to on (ACC).

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). However, if the shift lever is in any position other than P, even if the engine switch is pressed while the vehicle is stationary, the power source mode will not change to off, but to on (ACC). Move the shift lever to P, open the door and check that the steering lock operates.

      4. B003P9OC01
        *a Inspection Point

        Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.

        Tech Tips

        Perform the inspection for both inspection points.

      5. B003OX0C01
        *a Inspection Point

        Inspect the push start operating range (rear floor). Place the key on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box or on the floor.

        • Communication may not be possible if the key is within 0.2 m (0.66 ft.) of the center of the console box.

        Tech Tips

        Perform the inspection for both inspection points.

      6. B003Q7LC01
        *a Inspection Point

        Inspect the push start operating range (luggage room). Place the electrical key transmitter sub-assembly on the luggage room floor at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear corners of the luggage room.

        Tech Tips

        Perform the inspection for both inspection points.

    7. Check the push start function. (for Manual Transmission)


      1. With the engine switch off, depress the clutch pedal while carrying the electrical key transmitter sub-assembly and check that the smart warning light in the combination meter assembly illuminates green. Then, when the smart warning light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.

      2. With the clutch pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off).

      4. B003P9OC01
        *a Inspection Point

        Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.

        Tech Tips

        Perform the inspection for both inspection points.

      5. B003OX0C01
        *a Inspection Point

        Inspect the push start operating range (rear floor). Place the key on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box or on the floor.

        • Communication may not be possible if the key is within 0.2 m (0.66 ft.) of the center of the console box.

        Tech Tips

        Perform the inspection for both inspection points.

      6. B003Q7LC01
        *a Inspection Point

        Inspect the push start operating range (luggage room). Place the electrical key transmitter sub-assembly on the luggage room floor at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear corners of the luggage room.

        Tech Tips

        Perform the inspection for both inspection points.

    8. Check the entry cancel function.


      1. Cancel the smart entry and start system and check that all the functions of the smart entry and start system (for Entry Function) no longer operate.

        Note


        • Refer to the following procedures to cancel the smart entry and start system (for Entry Function).

          Click here

        • While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.

      2. While the key cancel function (entry cancel function) is on, check that all functions of the smart entry and start system cannot be operated.

    9. Check the answer-back function (hazard warning light flashing and buzzer sounding).

      Entry Operation Wireless Buzzer Hazard Warning Light
      Entry Door Lock Sounds once Flashes once
      Entry Door Unlock Sounds once Flashes once

  2. KEY DIAGNOSTIC MODE (Using GTS)

    Tech Tips


    • With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.

    • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


    1. Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check (Key Diag Mode).


      Body Electrical > Entry&Start > Utility
      Tester Display
      Communication Check(Key Diag Mode)

    2. Inspect the appropriate item according to the following table.

      Tester Display Inspection Item
      [CH1/CH2] Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) (for Driver Door)
      [CH1] Overhead + Driver Side*1
      [CH2] Overhead + Driver Side*1
      [CH1/CH2] Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) (for Front Passenger Door)
      [CH1] Overhead + Passenger Side*2
      [CH2] Overhead + Passenger Side*2
      [CH1/CH2] Overhead + Back Door*3 No. 2 indoor electrical key antenna assembly (back door)
      [CH1] Overhead + Back Door*3
      [CH1] Overhead + Back Door*3
      [CH1/CH2] Immobiliser Amp*4 Amplifier (engine switch)
      [CH1] Immobiliser Amp*4
      [CH2] Immobiliser Amp*4
      [CH1/CH2] Overhead + Room*5 No. 1 indoor electrical key antenna assembly (front floor)
      [CH1] Overhead + Room*5
      [CH2] Overhead + Room*5
      [CH1/CH2] Overhead + Room2*6 No. 2 indoor electrical key antenna assembly (rear floor)
      [CH1] Overhead + Room2*6
      [CH2] Overhead + Room2*6
      [CH1/CH2] Overhead + Room3*7 No. 2 indoor electrical key antenna assembly (inside luggage)
      [CH1] Overhead + Room3*7
      [CH2] Overhead + Room3*7

    3. Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.


      1. B003QJRC01
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        *1: Front door outside handle assembly (electrical key antenna) (for Driver Door)

        Tech Tips


        • Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for Driver Door) in the position shown in the illustration.

        • *2: Perform the same inspection for the front passenger side.

    4. B003QRUC01
      *a 0.7 to 1 m (2.30 to 3.28 ft.)

      *3: No. 2 indoor electrical key antenna assembly (back door)

      Tech Tips

      Hold the electrical key transmitter sub-assembly at the same height as the back door opener switch assembly and align it with the center of the rear of the vehicle as shown in the illustration.

    5. B003QR0C01
      *1 Engine Switch
      *2 Electrical Key Transmitter Sub-assembly

      *4: Amplifier (engine switch)

      Tech Tips

      While facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch.

    6. B003P9OC01
      *a Inspection Point

      *5: No. 1 indoor electrical key antenna assembly (front floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.

    7. B003OX0C01
      *a Inspection Point

      *6: No. 2 indoor electrical key antenna assembly (rear floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the console box.

    8. B003Q7LC01
      *a Inspection Point

      *7: No. 2 indoor electrical key antenna assembly (inside luggage)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the luggage room floor.