LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2789

DTC Code DTC Name
B2789 No Response from ID BOX

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2789 No Response from ID BOX No communication between the certification ECU and ID code box for 10 seconds or more.

  • ID code box (immobiliser code ECU)

  • Certification ECU (smart key ECU assembly)

  • Harness or connector

WIRING DIAGRAM

B003ONTE13

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the ignition switch off to troubleshoot:

    Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to the Service Bulletin.

Tech Tips

When the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Proceed to
      DTC B2789 is not output
      DTC B2789 is output

    DTC B2789 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B2789 is output

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU])


    1. Disconnect the G16 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the G138 ID code box (immobiliser code ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G16-5 (LIN) - G138-2 (LIN1) Always Below 1 Ω
      G16-5 (LIN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - BATTERY AND BODY GROUND)


    1. B003OQ9C16
      *a

      Front view of wire harness connector

      (to ID Code Box [Immobiliser Code ECU])

      Disconnect the ID code box (immobiliser code ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G138-5 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G138-1 (+B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Replace the ID code box (immobiliser code ECU) with a new one.

    2. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Proceed to
      DTC B2789 is not output
      DTC B2789 is output

    DTC B2789 is not output

    END (ID CODE BOX [IMMOBILISER CODE ECU] IS DEFECTIVE)

    DTC B2789 is output

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)