AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

As a result, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

PROCEDURE

1. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

   
   

   • *1: for LH Side

     *2: for RH Side

   
   

   1. Disconnect the G102 and G103 radio and display receiver assembly connectors.

   2. Disconnect the K4*1 and/or J3*2 front No. 1 speaker assembly connector.

   3. Disconnect the K7*1 and/or J6*2 front No. 2 speaker assembly connector.

   4. Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.

   5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH Side Tester Connection Condition Specified Condition G102-2 (FL+) - K7-4 (TWL+) Always Below 1 Ω G102-6 (FL-) - K7-2 (TWL-) Always Below 1 Ω K7-3 (+) - K4-1 Always Below 1 Ω K7-1 (-) - K4-2 Always Below 1 Ω G103-2 (RL+) - M2-1 Always Below 1 Ω G103-6 (RL-) - M2-2 Always Below 1 Ω G102-2 (FL+) or K7-4 (TWL+) - Body ground Always 10 kΩ or higher G102-6 (FL-) or K7-2 (TWL-) - Body ground Always 10 kΩ or higher K7-3 (+) or K4-1 - Body ground Always 10 kΩ or higher K7-1 (-) or K4-2 - Body ground Always 10 kΩ or higher G103-2 (RL+) or M2-1 - Body ground Always 10 kΩ or higher G103-6 (RL-) or M2-2 - Body ground Always 10 kΩ or higher
      for RH Side Tester Connection Condition Specified Condition G102-1 (FR+) - J6-4 (TWR+) Always Below 1 Ω G102-5 (FR-) - J6-2 (TWR-) Always Below 1 Ω J6-3 (+) - J3-1 Always Below 1 Ω J6-1 (-) - J3-2 Always Below 1 Ω G103-1 (RR+) - L2-1 Always Below 1 Ω G103-3 (RR-) - L2-2 Always Below 1 Ω G102-1 (FR+) or J6-4 (TWR+) - Body ground Always 10 kΩ or higher G102-5 (FR-) or J6-2 (TWR-) - Body ground Always 10 kΩ or higher J6-3 (+) or J3-1 - Body ground Always 10 kΩ or higher J6-1 (-) or J3-2 - Body ground Always 10 kΩ or higher G103-1 (RR+) or L2-1 - Body ground Always 10 kΩ or higher G103-3 (RR-) or L2-2 - Body ground Always 10 kΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

   
   

   1. Remove the front No. 1 speaker assembly.

      Click here

   2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

   OK

3. INSPECT REAR SPEAKER ASSEMBLY

   
   

   1. Remove the rear speaker assembly.

      Click here

   2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE REAR SPEAKER ASSEMBLY Click here

   OK

4. CHECK FRONT NO. 2 SPEAKER ASSEMBLY

   
   

   1. Replace the front No. 2 speaker assembly.

      Click here

   2. Check the malfunction disappears.

      OK
      Malfunction disappears.

      Tech Tips

      
      

      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH sides.

      Result
      Proceed to OK NG

   
   

   OK

   END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

   NG

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here