AUDIO AND VISUAL SYSTEM(for Radio and Display Type) OPERATION CHECK


  1. CHECK PANEL&STEERING SWITCH

    Tech Tips


    • The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NE2

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. B003MG7C01
      *A w/ DAB Function

      Select "Panel&Steering Switch" from the "Function Check/Setting" screen.

    4. B003S49N01

      Panel&Steering Switch Check Mode

      Screen Description
      Display Content
      *a: Switch condition "Pushed" is displayed when any switch is pushed.
      *b: Number of switches pushed

      • Number of switches pushed at once is displayed.

      • If more than 3 switches are pushed at once, "More than 3" is displayed.
      *c: Rotary switch direction Direction of rotary switch is displayed.

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note

        When the "AUDIO" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  2. CHECK TOUCH SWITCH

    Tech Tips


    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NE2

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. B003RM7C01
      *A w/ DAB Function

      Select "Touch Switch" from the "Function Check/Setting" screen.

    4. B003PCN

      Touch Switch Check


      1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tech Tips


        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after the finger is removed.

  3. CHECK MICROPHONE

    Tech Tips


    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NE2

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. B003MIDC01
      *A w/ DAB Function

      Select "Microphone Check" from the "Function Check/Setting" screen.

    4. B003RRIN01

      Microphone Check

      Screen Description
      Display Content
      *a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tech Tips

        The microphone is active at all times when this screen is displayed.

  4. CHECK VEHICLE SIGNAL

    Tech Tips


    • Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NE2

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. B003LJ8C01
      *A w/ DAB Function

      Select "Vehicle Signal" from the "Function Check/Setting" screen.

    4. B003PWL

      Vehicle Signal Check Mode

      Screen Description
      Display Content
      Battery Battery voltage is displayed.
      IG Ignition switch ON/OFF state is displayed.
      PKB Parking brake ON/OFF state is displayed.
      REV Reverse signal ON/OFF state is displayed.
      SPEED Vehicle speed is displayed in km/h.
      TAIL Tail signal (light control switch) ON/OFF state is displayed.
      ADIM/TCAN Brightness state DIM (with)/BRIGHT (without) is displayed.

      Tech Tips


      • Only items sending vehicle signals will be displayed.

      • This screen displays vehicle signals received by the radio and display receiver assembly.

      • This screen is updated once per second.


      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  5. CHECK HANDS-FREE VOICE QUALITY SETTING

    Tech Tips


    • The hands-free voice of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NE2

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. B003NQFC01
      *A w/ DAB Function

      Select "HF Voice Quality Setting" from the "Function Check/Setting" screen.

    4. B003R3YC01
      *a Numeric Keypad
      *b Setting Button
      *c Reset Button

      Hands-Free Voice Quality Setting


      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the numeric keypad on the screen to input the voice quality type according to the table.

        Settings
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality

        A

        (Noise)

        		 The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        B

        (Noise)

        		 The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        C

        (Echo)

        		 The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).

        D

        (Echo)

        		 The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
        Settings (When Multiple Phenomena Occurred)
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
        A+C The other party hears background noise and weak echoes when listening to your voice. 1100

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        A+D The other party hears background noise and strong echoes when listening to your voice. 1200

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).
        B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        Tech Tips


        • The default value is "0000".

        • Settings will be applied when the setting button is selected.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

  6. CHECK SPEAKER

    Tech Tips


    • This function is used when checking the speaker wiring and whether the speakers are functioning properly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Turn audio mode on and play any audio source.

      Tech Tips

      This audio source will be used for the speaker check.

    2. Enter diagnostic mode.

      Click here

    3. B003NZ0

      Select "Failure Diagnosis" from the "Service Menu" screen.

    4. B003Q6A

      Select "System Check" from the "Failure Diagnosis" screen.

    5. B003JFD

      Select "SPCheck ON" from the "System Check Mode" screen.

    6. Check the speaker wiring and check that the speakers are functioning properly.

      Tech Tips


      • Check that each speaker outputs sound from the selected audio source properly.

      • "SPCheck OFF" is displayed during the speaker check.

      • Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

      • More than one speaker may sound simultaneously depending on the speaker wiring.

    7. Sound stops when any of the following conditions are met:


      1. The "SPCheck OFF" switch is pressed.

      2. The ignition switch is turned off.

      3. Diagnostic mode is turned off.

      4. The screen is changed to another screen.

      5. Audio mode is turned off.

  7. CHECK DAB RECEPTION (w/ DAB Function)


    • The reception condition of DAB (Digital Audio Broadcast) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B003NZ0

      Select "Function Check/ Setting" from the "Service Menu" screen.

    3. B003S71

      Select "Next Page" from the "Function Check/Setting I" screen.

    4. B003Q5M

      Select "DAB Reception Check" from the "Function Check/Setting II" screen.

    5. B003K16N01

      DAB Reception Check

      Screen Description
      Display Content
      *a: Up or down switch Enables the channel to be changed to the one to be checked.
      *b: Check/STOP switch

      • Check: Starts checking

      • STOP: Stops checking
      *c: Antenna connection check

        Displays DAB antenna reception levels as follows:

      • OK: Connected properly

      • NG: Not connected properly

      • -: Not equipped with DAB antenna.
      *d: DAB tuner reception level check result description

        Displays DAB antenna reception levels as follows:

      • 111 or more: Font color is black (good reception).

      • 110 or less: Font color is red (poor reception).

      • -: Not equipped with DAB antenna.

      1. Select the "Check" button to start the DAB reception check.

      2. Check that the results are displayed when the DAB reception check is performed.

  8. CHECK SOFTWARE ERROR HISTORY

    Tech Tips

    This function is used to check the cause when the radio and display receiver assembly screen is blacked out.


    1. Check Software Error History.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Software Error History

      5. When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

        Software Error History Screen Description
        Error Description Trigger Detail
        Software Reset Navi Microcomputer Hexadecimal Number
        Audio Microcomputer
        CAN Microcomputer
        No Video Signal Front Monitor
        Rear Monitor
        MOST Cold Restart Always

        Tech Tips


        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear Software Error History.


      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  9. CHECK OPTICAL DISC ERROR HISTORY

    Tech Tips

    This function is used to check the cause of an optical disc error.


    1. Check Optical Disc Error History.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Optical Disc Error History

      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Optical Disc Error History Screen Description
        Display Content
        Error Type Displays the type of error.
        Device Displays the malfunctioning device.
        Date Displays the date and time that the malfunction occurred.
        "Error Type" Screen Description
        Error Type Detection Condition Action
        Read Error When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table.

        Click here

        Disc damaged/upside down/dirty

        When it is determined that any of the following is the cause of the disc read error:


        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.
        Cannot determine disc type An unsuitable disc is inserted.
        DPS error When an error occurs while decoding MP3/WMA/AAC files.
        Some files are corrupt

        • When MP3/WMA/AAC files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.
        Some files cannot be found

        • When a disc without music data is played back.

        • When there are no playable MP3/WMA/AAC files.
        Copy protection violation When a file with copyright protection that cannot be played back is played back.
        "Device" Screen Description
        Device Component
        DVD-P* Radio and display receiver assembly
        CD-P Radio and display receiver assembly
        R-Seat DVD-P Not available

        • *: w/ DVD Player

        Tech Tips


        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear Optical Disc Error History.


      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  10. Tech Tips


    • This function is used to detect disconnection of the video devices.

    • In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.

    CHECK VIDEO DEVICE CONNECTION CHECK


    1. Check Video Device Connection Check.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.


        Body Electrical > Navigation System > Utility
        Tester Display
        Video Device Connection Check

      5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

        Tech Tips


        • DTCs are stored when errors are detected.

        • Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

        Video Device Connection Check Screen Description
        Error Detected Image Line (Type) Areas to be Checked
        H/U - > Separate Display (GVIF) Not available
        H/U - > Full RSE (GVIF) Not available
        RSE - > Seat Back Display RH (GVIF) Not available
        RSE - > Seat Back Display LH (GVIF) Not available
        Rear Camera - > H/U (NTSC) NTSC video signal between the radio and display receiver assembly and rear television camera assembly
        IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
        IPA/BGM/PVM ECU - > H/U (NTSC) Not available
        IPA/BGM/PVM ECU - > H/U (GVIF) Not available

    2. Clear Video Device Connection Check.


      1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  11. Tech Tips

    This function is used to check the connection history when the connection between the radio and display receiver assembly and a "Bluetooth" device is unstable.

    CHECK "Bluetooth" CONNECTION HISTORY


    1. Check "Bluetooth" Connection History.

      Tech Tips


      • "Bluetooth" Connection History displays data stored in the internal memory of the ECU, such as the date a "Bluetooth" connection was attempted and the progress of a "Bluetooth" connection.

      • By checking "Bluetooth" Connection History, the date, cause, etc. of a "Bluetooth" device failing to register or connect can be analyzed.

      • "Bluetooth" connection history indicates the estimated cause of a malfunction, but does not determine it. Therefore, checking "Bluetooth" Connection History may not improve the problem.

      • Performing inspection using the GTS before recording the "Bluetooth" Connection History may clear the operation history.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Bluetooth Connection History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Bluetooth Connection History

      5. When an item is stored for "Bluetooth" Connection History, record it before proceeding with troubleshooting.

        "Bluetooth" Connection History Screen Description
        Item Content
        Occurrence Start Date/Time Date and time of "Bluetooth" connection are displayed.
        Occurrence End Date/Time Date and time of "Bluetooth" disconnection are displayed.
        History Type Type of "Bluetooth" Connection History is displayed.
        Result "Bluetooth" connection result is displayed.
        Contents "Bluetooth" connection status is displayed.
        "Bluetooth" Address "Bluetooth" device address is displayed.
        Continuance Time The number of retries when "Bluetooth" connection was performed is displayed.
        History Type: ACC ON
        Result Contents Detail Areas to be Checked
        - - Ignition switch ACC -
        History Type: Registration
        Result Contents Detail Areas to be Checked
        Success (HFP) No Error "Bluetooth" device was registered as a hands-free device properly. -
        Success (AVP) No Error "Bluetooth" device was registered as a "Bluetooth" audio device properly. -
        Failure Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Wrong PIN code was input for PIN code verification. Perform "Bluetooth" device registration again. (Input PIN code correctly.)
        Did not select the confirmation button even though a passkey was displayed. Perform "Bluetooth" device registration again. (When a passkey is displayed, select the confirmation button.)
        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device. Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.
        ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" device registration again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" device registration again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" device registration again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" device registration again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" device registration again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Memory Write Failure "Bluetooth" device information could not be stored in the radio and display receiver assembly. Perform "Bluetooth" device registration again.
        Other Error An error other than above occurred. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Cancel No Error Registration was suspended by operating the radio and display receiver assembly or "Bluetooth" device. -
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Success (HFP)

        • Manual Connect Success (HFP)

        		 No Error "Bluetooth" device was connected as a hands-free device properly. -

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        		 Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed. If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.
        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device. Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.
        Page Time Out Could not find a "Bluetooth" device near the radio and display receiver assembly. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        		 ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        SDP Error HFP was disabled on the "Bluetooth" device. Enable HFP on the "Bluetooth" device and perform "Bluetooth" connection again.
        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is hands-free compatible and its operation has been confirmed.

        Click here

        Other Error An error other than above occurred. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Manual Connect Cancel (HFP) No Error Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device. -
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Success (AVP)

        • Manual Connect Success (AVP)

        		 No Error "Bluetooth" device was connected as a "Bluetooth" audio device properly. -

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        		 Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed. If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.
        A verification error occurred between the radio and display receiver assembly and "Bluetooth" device. Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again.
        Page Time Out Could not find a "Bluetooth" device near the radio and display receiver assembly. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        		 ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        SDP Error AVP was disabled on the "Bluetooth" device. Enable AVP on the "Bluetooth" device and perform "Bluetooth" connection again.
        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is "Bluetooth" audio compatible and its operation has been confirmed.

        Click here

        Other Error An error other than above occurred. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Manual Connect Cancel (AVP) No Error Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device. -
        History Type: Disconnection
        Result Contents Detail Areas to be Checked
        Disconnection Complete (HFP) Link Loss The "Bluetooth" device was moved outside of the communication area. Move the "Bluetooth" device into the communication area.
        "Bluetooth" connection was disconnected due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Disconnection from Partner "Bluetooth" connection was disconnected by operating the "Bluetooth" device. -
        Disconnection from Self "Bluetooth" connection was disconnected by operating the radio and display receiver assembly. -
        Other Error An error other than above occurred. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Disconnection Complete (AVP) Link Loss The "Bluetooth" device was moved outside of the communication area. Move the "Bluetooth" device into the communication area.
        "Bluetooth" connection was disconnected due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Disconnection from Partner "Bluetooth" connection was disconnected by operating the "Bluetooth" device. -
        Disconnection from Self "Bluetooth" connection was disconnected by operating the radio and display receiver assembly. -
        Other Error An error other than above occurred. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        History Type: Send
        Result Contents Detail Areas to be Checked
        Success No Error Call was made properly. -
        Failure Out of Service Outside the cellular phone service area. Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate the device again.
        Redial Regulation Redial of the "Bluetooth" device was restricted and could not make a hands-free call. Restart the "Bluetooth" device and operate it again.
        Other Error Could not make a hands-free call due to a "Bluetooth" device malfunction. Restart the "Bluetooth" device and operate it again.
        Could not make a hands-free call due to a radio and display receiver assembly malfunction. After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again.
        Could not make a hands-free call from the radio and display receiver assembly because the call status of the "Bluetooth" device was not transmitted to the radio and display receiver assembly. Restart the "Bluetooth" device and operate it again.

    2. Clear "Bluetooth" Connection History.


      1. When DTCs are cleared using any of the following operations, "Bluetooth" Connection History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.