AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) Radio Broadcast cannot be Received (Bad Reception)

WIRING DIAGRAM

B003R14E02

PROCEDURE


  1. CHECK RADIO RECEIVER ASSEMBLY


    1. Check the radio automatic station search function by activating it.

      OK
      Automatic station search function stops on a station.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

  2. CHECK OPTIONAL COMPONENTS


    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      OK
      Optional components are installed.

      Note

      Do not remove optional components without the permission of the customer.

      Result
      Proceed to
      OK
      NG

    OK

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    NG

  3. CHECK RADIO RECEIVER ASSEMBLY


    1. B003OQ6

      Remove the antenna connector from the radio receiver assembly.

    2. Turn the ignition switch ACC with the radio receiver assembly connector connected.

    3. Turn the radio on and tune into AM mode.

    4. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK
      Noise can be heard from the speakers.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  4. INSPECT RADIO RECEIVER ASSEMBLY


    1. B003NQTE31

      Disconnect the RA radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  5. CHECK ANTENNA CORD SUB-ASSEMBLY


    1. B003LT5C01
      *a

      Front view of wire harness connector

      (to Radio Receiver Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Remove the antenna connector from the radio receiver assembly.

    2. Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      RA-3 (MAIN) - 2 Always Below 1 Ω
      RA-5 (ANT+) - 3 Always Below 1 Ω
      RA-3 (MAIN) - Body ground Always 10 kΩ or higher
      RA-5 (ANT+) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  6. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. B003QP5C01
      *a

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)

      Remove the antenna connector from the antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 3 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2 Always Below 1 Ω
      3 - 3 Always Below 1 Ω
      2 - Body ground Always 10 kΩ or higher
      3 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  7. CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. B003POQC01
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 1 Antenna Amplifier Assembly)

      Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 1 antenna amplifier assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2 Always Below 1 Ω
      3 - 1 Always Below 1 Ω
      2 - Body ground Always 10 kΩ or higher
      3 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  8. CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY


    1. Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

      Click here

      OK
      Radio broadcasts can be received normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here