FRONT WIPER MOTOR REMOVAL

PROCEDURE


  1. REMOVE FRONT WIPER ARM HEAD CAP


    1. B003JBHC01
      B003KT0 Protective Tape

      Using a screwdriver, detach the claw and remove the front wiper arm head cap.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for both front wiper arm head caps.

  2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. B003R20

      Remove the nut and front wiper arm and blade assembly RH.

  3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. B003RYV

      Remove the nut and front wiper arm and blade assembly LH.

  4. REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY RH


    1. B003K3FC01
      *a Claw A

      Detach the clip and disconnect the hood to cowl top seal from the fender apron mudguard seal sub-assembly RH.

    2. Detach claw A by hand from the bottom of the fender apron mudguard seal sub-assembly RH.

    3. Detach the claw and clip and remove the fender apron mudguard seal sub-assembly RH.

  5. REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure described for the RH side.

  6. REMOVE HOOD TO FRONT FENDER SEAL RH


    1. B003N3F

      Detach the claw and remove the hood to front fender seal RH.

  7. REMOVE HOOD TO FRONT FENDER SEAL LH

    Tech Tips

    Use the same procedure described for the RH side.

  8. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    1. B003R45C01
      B003OFB Remove in this Direction (1)
      B003QYY Remove in this Direction (2)

      Detach the claw and guide and remove the front fender to cowl side seal RH as shown in the illustration.

  9. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

    Tech Tips

    Use the same procedure described for the RH side.

  10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. B003JN0

      Remove the 2 clips.

    2. B003M8FC01
      B003OFB Remove in this Direction

      Detach the claw.

    3. B003JU0C01
      B003OFB Remove in this Direction

      Pull the cowl top ventilator louver sub-assembly in the direction indicated by the arrow in the illustration to detach the guide and remove the cowl top ventilator louver sub-assembly.

  11. REMOVE HOOD TO COWL TOP SEAL


    1. B003M3T

      Detach the claw and clip and remove the hood to cowl top seal.

  12. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Note

    Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.


    1. B003QHHC01
      *1 Motor Grommet
      B003R2S Connector
      B003LF2 Bolt
      B003OFB Remove in this Direction

      Disconnect the connector.

    2. Remove the 2 bolts.

    3. Detach the motor grommet as shown in the illustration and remove the windshield wiper motor and link assembly.

  13. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    1. B003QTCC01
      B003KT0 Protective Tape
      B003OFB Remove in this Direction

      Using a screwdriver, disconnect the No. 1 windshield wiper link rod from the front wiper crank pivot.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B003MMT

      Using a T30 "TORX" socket wrench, remove the 2 bolts and windshield wiper motor assembly.