REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door disassembly/reassembly are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal

    w/ Power Back Door System:

  • Reset back door close position

 Power back door system

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

  • Fully open the rear door glass sub-assembly RH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR FRAME GARNISH RH


    1. B003MKZ

      Detach the clip and claw and remove the rear door frame garnish RH.

  4. REMOVE REAR ARMREST ASSEMBLY RH


    1. B003KNDC01
      B003R2S Order of Removal
      B003OFB Remove in this Direction

      Detach the clip and claw and remove the rear armrest assembly RH.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. B003JKHC01
      B003OFB Remove in this Direction

      Detach the clip and claw.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  8. REMOVE REAR DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)


    1. B003NJOC01
      *A for RH side
      *B for LH side
      B003KT0 Protective Tape
      B003OFB Remove in this Direction (1)
      B003QYY Remove in this Direction (2)

      Put protective tape around the reflex reflector.

    2. Using a thin-bladed screwdriver, detach the claw and guide.

      Tech Tips

      Tape the thin-bladed screwdriver tip before use.

    3. Remove the rear door trim reflector RH.

  9. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG RH


    1. B003MJG

      Using moulding remover A, detach the claw and remove the rear door inside handle bezel plug RH as shown in the illustration.

  10. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY RH


    1. B003KZ4

      Remove the 3 screws.

    2. B003MCXC01
      B003QBX Place Hands Here
      B003R2S Order of Removal (1)
      B003LF2 Order of Removal (2)
      B003OFB Remove in this Direction

      Detach the clip as shown in the illustration.

    3. B003QVMC01
      B003OFB Remove in this Direction

      Detach the guide and remove the rear door trim board sub-assembly RH as shown in the illustration.

    4. B003JILC02
      *1 Rear Door Inside Looking Cable Assembly RH
      *2 Rear Door Lock Remote Control Cable Assembly RH
      B003OFB Remove in this Direction

      Detach the clamp and disconnect the rear door lock remote control cable assembly RH and rear door inside looking cable assembly RH as shown in the illustration.

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY RH


    1. B003RHDC01
      B003OFB Remove in this Direction

      Detach the claw and guide and remove the rear door inside handle sub-assembly RH.

  12. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP RH


    1. B003RQPC01
      B003OFB Remove in this Direction

      Raise the claw of the rear door inner glass weatherstrip RH as shown in the illustration, and then remove the rear door inner glass weatherstrip RH from the rear door trim board sub-assembly RH.

  13. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  14. REMOVE REAR DOOR SERVICE HOLE COVER RH


    1. B003MS2C01
      B003QY9 Butyl Tape

      Pull out the rear door lock remote control cable assembly RH, rear door inside locking cable assembly RH and wire harness from the rear door service hole cover RH, and then remove the rear door service hole cover RH.

      Note

      Remove any remaining butyl tape from the rear door panel.

  15. REMOVE SCREW GROMMET


    1. B003RN3

      Using a clip remover, detach the claw and remove the 2 screw grommets.

  16. REMOVE REAR DOOR GLASS RUN RH


    1. B003J8H

      Detach the guide and remove the rear door glass run RH.

  17. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY RH


    1. B003O0OC01
      B003R2S Bolt
      B003LF2 Screw

      Lift up the rear door weatherstrip RH and remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly RH.

  18. REMOVE REAR DOOR GLASS SUB-ASSEMBLY RH


    1. B003SFZ

      Remove the rear door glass sub-assembly RH from the rear door window regulator sub-assembly RH as shown in the illustration.

    2. B003KZ5C01
      B003OFB Remove in this Direction (1)
      B003QYY Remove in this Direction (2)

      Remove the rear door glass sub-assembly RH as indicated by the arrows in the order shown in the illustration.

      Note

      Be careful not to damage the rear door glass sub-assembly RH.

  19. REMOVE REAR DOOR QUARTER WINDOW GLASS RH


    1. B003L5BC01
      B003OFB Remove in this Direction

      Remove the rear door quarter window glass RH together with the rear door quarter window weatherstrip RH.

  20. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP RH


    1. B003QRR

      Remove the rear door quarter window weatherstrip RH from the rear door quarter window glass RH.

  21. REMOVE REAR DOOR REAR BELT MOULDING RH

    Tech Tips

    The procedure described below is for the LH side.

    Click here

  22. REMOVE REAR DOOR BELT MOULDING ASSEMBLY RH

    Tech Tips

    The procedure described below is for the LH side.

    Click here

  23. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH


    1. B003Q54C01
      B003R2S Bolt
      B003LF2 Connector
      B003QHB Temporarily Bolt

      Disconnect the connector.

    2. Loosen the temporarily bolt.

      Note

      Do not remove the temporarily bolt. If the temporarily bolt is removed, the rear door window regulator sub-assembly RH may fall and become damaged.

    3. Remove the 4 bolts and rear door window regulator sub-assembly RH.

  24. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Click here

  25. REMOVE REAR DOOR LOCK CHILD PROTECTION COVER RH


    1. B003K8V

      Remove the rear door lock child protection cover RH.

  26. REMOVE REAR DOOR LOCK ASSEMBLY RH

    Click here

  27. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY RH

    Click here

  28. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

    Click here

  29. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY RH

    Click here

  30. REMOVE DOOR LOCK WIRING HARNESS SEAL

    Click here

  31. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. B003QKYC01
      B003OFB Remove in this Direction

      Using a T30 "TORX" socket wrench, loosen the screw.

    2. Detach the claw and remove the rear door outside handle cover as shown in the illustration.

  32. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY RH


    1. B003M0CC01
      B003OFB Remove in this Direction

      Remove the rear door outside handle assembly RH as shown in the illustration.

  33. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B003OYOC01
      B003OFB Remove in this Direction

      Detach the claw and remove the rear door front outside handle pad.

  34. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B003OTHC01
      B003OFB Remove in this Direction

      Detach the claw and remove the rear door rear outside handle pad.

  35. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH


    1. B003O5IC01
      *a Grommet
      *b Guide
      B003OFB Remove in this Direction

      Using a T30 "TORX" socket wrench, loosen the screw.

    2. Detach the grommet and guide and remove the rear door outside handle frame sub-assembly RH.

  36. REMOVE REAR DOOR PANEL CUSHION


    1. B003LS9

      Detach the claw and remove the 2 rear door panel cushions.

  37. REMOVE REAR DOOR CHECK ASSEMBLY RH


    1. B003R1LC01
      B003R2S Bolt (A)
      B003LF2 Bolt (B)

      Remove the 2 bolts (A), bolt (B) and rear door check assembly RH.

  38. REMOVE REAR DOOR WEATHERSTRIP RH


    1. B003R1MC01
      B003KT0 Double-sided Tape

      Using a clip remover, detach the clip and remove the rear door weatherstrip RH.

      Note

      Remove any remaining double-sided tape from the rear door panel RH.

  39. REMOVE REAR DOOR DUST PROOF SEAL


    1. B003JZ2

      Detach the claw and remove the 3 rear door dust proof seals.

  40. REMOVE NO. 2 BLACK OUT TAPE RH

    Tech Tips

    The procedure described below is for the LH side.

    Click here

  41. REMOVE NO. 3 BLACK OUT TAPE RH

    Tech Tips

    The procedure described below is for the LH side.

    Click here