QUARTER WINDOW GLASS REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the quarter window glass removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal

w/ Power Back Door System:

Reset back door close position

 Power door lock control system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B003NO4

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B003RP6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  4. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  5. REMOVE BACK DOOR SCUFF PLATE

    Click here

  6. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    Click here

  7. REMOVE REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

    Click here

  8. REMOVE QUARTER INSIDE TRIM BOARD LH

    Click here

  9. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

  10. REMOVE QUARTER PILLAR GARNISH LH

    Click here

  11. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

  12. REMOVE UPPER REAR PILLAR GARNISH LH

    Click here

  13. REMOVE UPPER QUARTER WINDOW MOULDING LH

    Click here

  14. REMOVE QUARTER WINDOW ASSEMBLY LH

    Note


    • Be careful not to damage the quarter window assembly LH as the clips are installed to the quarter window assembly LH.

    • The quarter window assembly LH may fall while performing this procedure. Therefore, use suction cups to hold the quarter window assembly LH from the outside of the vehicle.


    1. Using a knife, cut off the moulding as shown in the illustration.

      B003KB0C01
      *a Cut - -

      Note

      Be careful not to damage the vehicle body with the knife.

    2. Remove the remaining moulding.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

    3. Put protective tape on the body panel around the quarter window assembly LH.

      B003PWBC01
      B003KT0 Protective Tape - -

    4. Install the suction cups to the quarter window assembly LH.

    5. B003MOQC01
      *a Piano Wire

      Insert a piano wire (approx. 0.6 mm) at the locations shown in the illustration, and tie objects that can serve as handles (for example, wooden blocks) to the wire ends.

    6. Pull on the ends of the piano wire alternately and leave the clips when cutting through the adhesive.

      Note


      • Do not forcefully brush the piano wire against the quarter window assembly LH.

      • Be careful as the piano wire will break if it crosses itself.

    7. B003KDX

      Using suction cups, detach the 4 clips and remove the quarter window assembly LH.

      Note

      Make sure that the quarter window assembly LH does not fall.

      Tech Tips

      Cut the clip if it is difficult to detach.

  15. REMOVE REAR QUARTER WINDOW GLASS RETAINER SUB-ASSEMBLY LH


    1. B003RK3

      Remove the screw.

    2. Using a clip remover, detach the clip and remove the rear quarter window glass retainer sub-assembly LH.