POWER WINDOW MASTER SWITCH INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Entry and Start System)

   
   
   1. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

      for RHD:

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection Switch Condition Specified Condition 3 (U) - 4 (A) 4 (A) - 9 (E) 6 (D) - 7 (B) Auto UP (for driver door) Below 1 Ω Not operated 10 kΩ or higher 3 (U) - 9 (E) 6 (D) - 7 (B) Manual UP (for driver door) Below 1 Ω Not operated 10 kΩ or higher 3 (U) - 7 (B) 6 (D) - 9 (E) Manual DOWN (for driver door) Below 1 Ω Not operated 10 kΩ or higher 3 (U) - 7 (B) 4 (A) - 6 (D) 6 (D) - 9 (E) Auto DOWN (for driver door) Below 1 Ω Not operated 10 kΩ or higher 3 (U) - 6 (D) 6 (D) - 7 (B) OFF (for driver door) Below 1 Ω 7 (B) - 10 (U) 9 (E) - 18 (D) Manual UP (for front passenger door) Below 1 Ω Not operated 10 kΩ or higher 7 (B) - 18 (D) 9 (E) - 10 (U) Manual DOWN (for front passenger door) Below 1 Ω Not operated 10 kΩ or higher 9 (E) - 18 (D) 10 (U) - 18 (D) OFF (for front passenger door) Below 1 Ω 7 (B) - 15 (U) 9 (E) - 16 (D) Manual UP (for rear RH door) Below 1 Ω Not operated 10 kΩ or higher 7 (B) - 16 (D) 9 (E) - 15 (U) Manual DOWN (for rear RH door) Below 1 Ω Not operated 10 kΩ or higher 9 (E) - 16 (D) 15 (U) - 16 (D) OFF (for rear RH door) Below 1 Ω 7 (B) - 12 (U) 9 (E) - 13 (D) Manual UP (for rear LH door) Below 1 Ω Not operated 10 kΩ or higher 7 (B) - 13 (D) 9 (E) - 12 (U) Manual DOWN (for rear LH door) Below 1 Ω Not operated 10 kΩ or higher 12 (U) - 13 (D) 9 (E) - 13 (D) OFF (for rear LH door) Below 1 Ω

         
         

         • If the result is not as specified, replace the power window regulator master switch assembly.

   2. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

      for LHD:

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection Switch Condition Specified Condition 1(E) - 4 (A) 3 (D) - 7 (B) 4 (A) - 6 (U) Auto UP (for driver door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 6 (U) 3 (D) - 7 (B) Manual UP (for driver door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 3 (D) 6 (U) - 7 (B) Manual DOWN (for driver door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 3 (D) 3 (D) - 4 (A) 6 (U) - 7 (B) Auto DOWN (for driver door) Below 1 Ω Not operated 10 kΩ or higher 3 (D) - 6 (U) 6 (U) - 7 (B) OFF (for driver door) Below 1 Ω 1(E) - 18 (D) 7 (B) - 10 (U) Manual UP (for front passenger door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 10 (U) 7 (B) - 18 (D) Manual DOWN (for front passenger door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 18 (D) 10 (U) - 18 (D) OFF (for front passenger door) Below 1 Ω 1(E) - 16 (D) 7 (B) - 15 (U) Manual UP (for rear RH door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 15 (U) 7 (B) - 16 (D) Manual DOWN (for rear RH door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 16 (D) 15 (U) - 16 (D) OFF (for rear RH door) Below 1 Ω 1(E) - 13 (D) 7 (B) - 12 (U) Manual UP (for rear LH door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 12 (U) 7 (B) - 13 (D) Manual DOWN (for rear LH door) Below 1 Ω Not operated 10 kΩ or higher 1(E) - 13 (D) 12 (U) - 13 (D) OFF (for rear LH door) Below 1 Ω

         
         

         • If the result is not as specified, replace the power window regulator master switch assembly.

   3. Check that the LED illuminates.

      
      
      1. 

         *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

         for RHD:

         Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 17 (ILL+) Battery negative (-) → 5 (ILL-) LED illuminates

         If the result is not as specified, replace the power window regulator master switch assembly.

      2. 

         *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

         for LHD:

         Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 11 (ILL+) Battery negative (-) → 5 (ILL-) LED illuminates

         If the result is not as specified, replace the power window regulator master switch assembly.

2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Entry and Start System)

   
   
   1. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

      Check that the LED illuminates.

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 3 (ILL+) Battery negative (-) → 13 (ILL-) LED illuminates

         If the result is not as specified, replace the power window regulator master switch assembly.