FRONT DIFFERENTIAL CARRIER ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | CLUTCH RELEASE CYLINDER ASSEMBLY | *2 | NO. 1 ENGINE UNDER COVER |
| *3 | NO. 2 ENGINE UNDER COVER | *4 | POWER STEERING LINK ASSEMBLY |
| *5 | STEERING SLIDING YOKE | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for Automatic Transmission | - | - |
| *1 | NO. 1 ENGINE UNDER COVER | *2 | NO. 2 ENGINE UNDER COVER |
| *3 | POWER STEERING LINK ASSEMBLY | *4 | STEERING SLIDING YOKE |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | FRONT DIFFERENTIAL CARRIER ASSEMBLY | *2 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *3 | FRONT DRIVE SHAFT ASSEMBLY RH | *4 | FRONT PROPELLER SHAFT ASSEMBLY |
| *5 | OIL TEMPERATURE SENSOR | *6 | FRONT DIFFERENTIAL BREATHER HOSE |
| *7 | FRONT DRIVE SHAFT HOLE SNAP RING | *8 | FRONT NO. 1 DIFFERENTIAL SUPPORT |
| *9 | FRONT NO. 2 DIFFERENTIAL SUPPORT | *10 | FRONT NO. 3 DIFFERENTIAL SUPPORT |
| *11 | DIFFERENTIAL MOUNT NUT | *12 | UPPER DIFFERENTIAL MOUNT STOPPER |
| *13 | LOWER DIFFERENTIAL MOUNT STOPPER | *14 | DIFFERENTIAL BREATHER TUBE BRACKET |
| *15 | DIFFERENTIAL MOTOR ACTUATOR CONNECTOR | *16 | OIL TEMPERATURE SENSOR |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Differential oil |
 |
MP grease |  |
Do not apply lubricants |
ILLUSTRATION
| *A | w/ A.D.D. | - | - |
| *1 | DIFFERENTIAL CLUTCH HUB | *2 | DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY |
| *3 | DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH | *4 | DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH |
| *5 | FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR | *6 | FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH |
| *7 | FRONT DIFFERENTIAL TUBE ASSEMBLY | *8 | SNAP RING |
| *9 | NEEDLE BEARING | *10 | SIDE GEAR SHAFT HOLE SNAP RING |
| *11 | DIFFERENTIAL CLUTCH SLEEVE | *12 | DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY |
| *13 | SIDE GEAR INTERMEDIATE SHAFT HOLE SNAP RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *A | w/o A.D.D. | - | - |
| *1 | DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH | *2 | DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH |
| *3 | FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH | *4 | FRONT DIFFERENTIAL TUBE ASSEMBLY |
| *5 | SNAP RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL DRIVE PINION | *2 | FRONT DIFFERENTIAL CARRIER OIL SEAL |
| *3 | FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER | *4 | FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
| *5 | FRONT DIFFERENTIAL OIL STORAGE RING | *6 | FRONT DRIVE PINION COMPANION FLANGE NUT |
| *7 | FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR | *8 | FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER) |
| *9 | FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER) | *10 | FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER) |
| *11 | FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER) | *12 | DRIVE PINION PLATE WASHER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Hypoid gear oil LSD |
| *T1 | 370 (3773, 273) or less | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL CASE ASSEMBLY | *2 | DIFFERENTIAL RING GEAR |
| *3 | DIFFERENTIAL SIDE BEARING RETAINER | *4 | FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING |
| *5 | FRONT DIFFERENTIAL CARRIER ASSEMBLY | *6 | FRONT DIFFERENTIAL UNION |
| *7 | PLATE WASHER | *8 | FRONT DIFFERENTIAL CASE BEARING (INNER) |
| *9 | FRONT DIFFERENTIAL CASE BEARING (OUTER) | *10 | FILLER PLUG |
| *11 | DRAIN PLUG | *12 | GASKET |
| *13 | STRAIGHT PIN | *14 | DIFFERENTIAL SIDE GEAR |
| *15 | DIFFERENTIAL PINION GEAR | *16 | DIFFERENTIAL PINION SHAFT |
| *17 | DIFFERENTIAL SIDE GEAR THRUST WASHER | *18 | DIFFERENTIAL PINION GEAR THRUST WASHER |
| *19 | DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Hypoid gear oil |
| ★ | Precoated part | - | - |