VANE PUMP(for 1GR-FE) REASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.

PROCEDURE


  1. INSTALL VANE PUMP HOUSING OIL SEAL


    1. B003KKGN01

      Using SST and a press, press in a new vane pump housing oil seal.

      SST
      09950-60010   ( 09951-00280 )
      09950-70010   ( 09951-07100 )

      Note


      • Make sure to install the vane pump housing oil seal so that it faces the correct direction.

      • Be careful not to damage the vane pump housing oil seal.

    2. Coat the lip of vane pump housing oil seal with MP grease.

  2. INSTALL SHAFT WITH PULLEY


    1. B003NGTC01
      *a power steering fluid

      Coat the inside surface of the bushing in the front housing with power steering fluid.

    2. Install the shaft with pulley to the front housing.

      Note


      • Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.

      • Be careful not to damage the vane pump housing oil seal.

  3. INSTALL FRONT VANE PUMP SIDE PLATE


    1. B003PZUC01
      B003R2S Power Steering Fluid

      Coat a new O-ring with power steering fluid and install it to the front housing.

    2. B003OH8C01
      B003R2S Power Steering Fluid
      B003OFB Install in this Direction

      Coat a new O-ring with power steering fluid and install it to the front vane pump side plate.

    3. B003JHG

      Install the front vane pump side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

      Note

      Be sure to install the front vane pump side plate in the correct position and with the correct orientation.

  4. INSTALL VANE PUMP CAM RING


    1. B003PVQC02
      *a Inscribed Mark

      With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

      Note

      Be sure to install the vane pump cam ring in the correct position and with the correct orientation.

  5. INSTALL VANE PUMP ROTOR


    1. B003RA2C01
      *1 Inscribed Mark
      *a Round End

      Install the vane pump rotor with the inscribed mark facing outward.

    2. Coat the 10 vane plates with power steering fluid.

    3. Install the vane pump rotor with the round ends facing outward.

  6. INSTALL VANE PUMP SHAFT SNAP RING


    1. B003ODO

      Using a snap ring expander, install a new snap ring onto the pulley shaft.

  7. INSTALL REAR HOUSING


    1. Coat the vane pump rear housing of the shaft sub-assembly with pulley and the surrounding surface with power steering fluid.

    2. Coat a new O-ring with power steering fluid and install it to the rear housing.

    3. Align the straight pin of the rear housing with the dent of the cam ring, side plate and front housing.

      Note

      Make sure that the O-ring is not out of position before installing the rear housing.

    4. Install the rear housing with the 4 bolts.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

  8. INSPECT ROTATING TORQUE


    1. B003K7XC01
      *a Service Bolt

      Check that the vane pump assembly rotates smoothly without abnormal noise.

    2. Provisionally install the service bolt.

      Recommended Service Bolt
      Item Specified Condition
      Thread Diameter 10 mm (0.394 in.)
      Thread Pitch 1.25 mm (0.0492 in.)
      Bolt Length 50 mm (1.97 in.)

    3. Using a torque wrench, check the pump rotating torque.

      Standard rotating torque
      0.27 N*m (3 kgf*cm, 2 in.*lbf) or less

      If the rotating torque is not as specified, check the installation of the housing oil seal.

  9. INSTALL POWER STEERING SUCTION PORT UNION


    1. Coat a new O-ring with power steering fluid, and install it onto the suction port union.

    2. Install the suction port union with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  10. INSTALL FLOW CONTROL VALVE


    1. Coat the flow control valve compression spring and flow control valve with power steering fluid.

    2. B003LZV

      Install the flow control valve compression spring.

    3. Install the flow control valve so that it faces the correct direction.

    4. Coat a new O-ring with power steering fluid and install it to the pressure port union.

    5. Install the pressure port union.

      Torque:
      69 N*m  { 704 kgf*cm, 51 ft.*lbf }