STARTER(for 2.0 kW Type) INSPECTION

PROCEDURE


  1. INSPECT STARTER ASSEMBLY

    CAUTION:

    As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

    Note

    The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.


    1. Mount the starter assembly in a vise between aluminum plates.

    2. Perform a pull-in test.


      1. Detach the wire harness clamp, remove the nut and disconnect the lead wire from terminal C.

      2. B003KV8C01
        *a Terminal C
        *b Terminal 50

        Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.

        If the clutch pinion gear does not extend, replace the magnet starter switch assembly.

    3. Perform a holding test.


      1. B003QV8C01
        B003R2S Disconnect

        Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

        If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

    4. Inspect the clutch pinion gear return.


      1. B003PGUC01
        B003R2S Disconnect
        B003LF2 Returns Inward

        Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

        If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

    5. Perform an operation test without load.


      1. Attach the wire harness clamp, connect the lead wire to terminal C with the nut.

        Torque:
        5.9 N*m  { 60 kgf*cm, 52 in.*lbf }
      2. B003QYDC01
        *a Terminal 50
        *b Terminal 30

        Connect the battery and an ammeter to the starter assembly as shown in the illustration.

      3. Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

        Standard current
        100 A or less at 11.5 V

        If the result is not as specified, replace the starter assembly.

  2. INSPECT MAGNET STARTER SWITCH ASSEMBLY


    1. B003SB9C02
      *a Terminal C
      *b Terminal 50
      *c Switch Body

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 50 - Terminal C Always Below 1 Ω
      Terminal 50 - Switch body Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  3. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    1. B003NTF

      Inspect the load of the brush spring.


      1. Take a pull scale reading immediately after the brush spring separates from the brush.

        Standard spring load
        22 to 28 N (2 to 3 kgf, 4.9 to 6.3 lbf)
        Minimum spring load
        12 N (1 kgf, 2.7 lbf)

        If the load is less than the minimum, replace the starter brush holder assembly.

    2. Check the resistance.


      1. B003LKK

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Positive (+) brush holder - Negative (-) brush holder Always 10 kΩ or higher

        If the result is not as specified, replace the starter brush holder assembly.

    3. Check the brush length.


      1. B003OEBC01
        *a Length

        Using a vernier caliper, measure the brush length.

        Standard length
        15 mm (0.591 in.)
        Minimum length
        9.0 mm (0.354 in.)

        If the length is less than the minimum, replace the starter brush holder assembly.

  4. INSPECT STARTER YOKE ASSEMBLY


    1. Check the resistance.


      1. B003MZOC01
        *a Lead Wire
        *b Brush
        *c Shunt Coil Terminal

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Lead wire - Brush Always Below 1 Ω
        Shunt coil terminal - Shunt coil terminal 20°C (68°F) 1.5 to 1.9 Ω

        If the result is not as specified, replace the starter yoke assembly.

    2. Check the brush length.


      1. B003R3TC01
        *a Length

        Using a vernier caliper, measure the brush length.

        Standard length
        15 mm (0.591 in.)
        Minimum length
        9.0 mm (0.354 in.)

        If the length is less than the minimum, replace the starter yoke assembly.

  5. INSPECT STARTER ARMATURE ASSEMBLY


    1. Check the commutator for dirt and/or burns on the surface.

      If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

    2. Check the resistance.


      1. B003Q5XC01
        *a Segment
        *b Coil Core

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Segment - Segment Always Below 1 Ω
        Segment - Coil core 10 kΩ or higher

        If the result is not as specified, replace the starter armature assembly.

    3. B003QE1

      Check the commutator circle runout.


      1. Place the armature on V-blocks.

      2. Using a dial indicator, measure the circle runout.

        Maximum circle runout
        0.05 mm (0.00197 in.)

        If the circle runout is more than the maximum, replace the starter armature assembly.

    4. Check the commutator.


      1. B003Q78

        Using a vernier caliper, measure the commutator diameter.

        Standard diameter
        35 mm (1.38 in.)
        Minimum diameter
        34 mm (1.34 in.)

        If the diameter is less than the minimum, replace the starter armature assembly.

      2. B003LX3

        Using a vernier caliper, measure the undercut depth of the commutator.

        Standard undercut depth
        0.7 mm (0.0276 in.)
        Minimum undercut depth
        0.2 mm (0.00787 in.)

        If the undercut depth is less than the minimum, correct it with a hacksaw blade.

    5. Inspect the armature bearings.


      1. Check that the armature bearings rotate smoothly.

        If the result is not as specified, replace the starter armature assembly.

  6. INSPECT STARTER CLUTCH SUB-ASSEMBLY


    1. B003O99C01
      B003R2S Free
      B003LF2 Lock

      Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

      If the result is not as specified, replace the starter clutch sub-assembly.

    2. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

      If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.