OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

  • B003MF5

    To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.

PROCEDURE


  1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

  2. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

  3. DRAIN ENGINE OIL

    CAUTION:

    To prevent burns, do not remove the oil pan drain plug while the engine is hot.


    1. Remove the oil filler cap assembly.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Clean and install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  4. REMOVE OIL FILTER SUB-ASSEMBLY

    CAUTION:

    To prevent burns, do not remove the oil filter sub-assembly while the engine is hot.


    1. B003KSSN01

      Using SST, remove the oil filter sub-assembly.

      SST
      09228-07501

      Tech Tips


      • Before removing the oil filter sub-assembly, place cloth where the oil may splash.

      • Use a container to catch the draining engine oil.

  5. INSTALL OIL FILTER SUB-ASSEMBLY


    1. Check and clean the oil filter sub-assembly installation surface.

    2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

    3. Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

    4. Using SST, tighten the oil filter sub-assembly.

      SST
      09228-07501
      B003KR5C01
      B003R2S 3/4 Turn - -

      1. Depending on the space available, choose from the following.

        If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      2. If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.

  6. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap assembly.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API-CF-4, CF or ACEA B1

      - 5W-30

      - 10W-30

      - 15W-40
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter sub-assembly change 7.0 liters (7.4 US qts, 6.2 Imp. qts)
      Drain and refill with oil filter sub-assembly change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
      Dry fill 8.0 liters (8.5 US qts, 7.0 Imp. qts)

  7. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  8. INSPECT ENGINE OIL LEVEL

    Click here

  9. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  10. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here