OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filter sub-assemblies must be disposed of at designated disposal sites.

  • B003MF5

    To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.

PROCEDURE


  1. REMOVE NO. 2 ENGINE UNDER COVER

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Wipe the oil pan sub-assembly and drain plug.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  3. REMOVE OIL FILTER SUB-ASSEMBLY


    1. B003SEYC01
      *a Hose
      *b Container

      Connect a hose with an inside diameter of 7.5 mm (0.295 in.) to the oil cooler cover sub-assembly.

    2. Put the drain oil container beneath the hose to collect the engine oil from the oil filter sub-assembly.

    3. B003RJ8N01

      Using SST, remove the oil filter sub-assembly.

      SST
      09228-07501

    4. Remove the hose from the oil cooler cover sub-assembly.

    5. Clean the oil cooler cover sub-assembly.

  4. INSTALL OIL FILTER SUB-ASSEMBLY


    1. Check and clean the oil filter sub-assembly installation surface.

    2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

    3. Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

    4. B003PN1N01

      Using SST, tighten the oil filter sub-assembly. Depending on the space available, choose from the following.

      SST
      09228-07501

      1. If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      2. If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.

  5. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      API CF-4, CF or ACEA B1

      (You may also use API CE or CD)

      - 5W-30

      - 10W-30

      - 15W-40

      - 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter sub-assembly change 6.6 liters (7.0 US qts, 5.8 Imp. qts)
      Drain and refill with oil filter sub-assembly change 6.9 liters (7.3 US qts, 6.1 Imp. qts)
      Dry fill 7.4 liters (7.8 US qts, 6.5 Imp. qts)

    2. Install the oil filler cap.

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  7. INSPECT ENGINE OIL LEVEL

    Click here

  8. INSTALL NO. 2 ENGINE UNDER COVER

    Click here