REAR SPEED SENSOR INSTALLATION

PROCEDURE


  1. INSTALL REAR SPEED SENSOR (for Rear Disc Brake)


    1. for RH:

      B003PXN

      1. Install the rear speed sensor RH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Attach the 8 clamps.

        Note

        When attaching the clamps, do not twist the wire harness.

      3. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

    2. for LH:

      B003M7J

      1. Install the rear speed sensor LH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Attach the 3 clamps.

        Note

        When attaching the clamp, do not twist the wire harness.

      3. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

  2. INSTALL REAR SPEED SENSOR (for Rear Drum Brake)


    1. for RH:

      B003KJO

      1. Install the rear speed sensor RH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Attach the 8 clamps.

        Note

        When attaching the clamps, do not twist the wire harness.

      3. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

    2. for LH:

      B003RN6

      1. Install the rear speed sensor LH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Attach the 3 clamps.

        Note

        When attaching the clamp, do not twist the wire harness.

      3. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

  3. INSTALL REAR WHEEL

    Click here

  4. CHECK SPEED SENSOR SIGNAL


    1. w/ VSC:

      Click here

    2. w/o VSC:

      Click here