FRONT SPEED SENSOR INSTALLATION

PROCEDURE


  1. INSTALL FRONT SPEED SENSOR LH


    1. B003LVL

      Install the skid control sensor clamp to the steering knuckle with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

    2. Install the front speed sensor LH to the steering knuckle with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

      • While inserting the speed sensor into the steering knuckle hole, do not strike or damage the sensor tip.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • When installing the sensor, do not twist the wire harness.

    3. B003S1G

      Install the harness clamp with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    4. Attach the clamp.

    5. B003NO1

      Attach the clamp.

    6. Install the 2 harness clamps with the 2 bolts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the clamps, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    7. B003REG

      Attach the 2 clamps.

      Note

      When attaching the clamps, do not twist the wire harness.

    8. B003KJZ

      Attach the 2 clamps.

      Note

      When attaching the clamps, do not twist the wire harness.

    9. Connect the connector and attach the clamp.

      Note


      • Do not attach the connector to the radiator fan shroud before connecting the connector.

      • Securely connect the connector.

  2. INSTALL FRONT SPEED SENSOR RH


    1. B003RXX

      Install the skid control sensor clamp to the steering knuckle with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

    2. Install the front speed sensor RH to the steering knuckle with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

      • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • When installing the sensor, do not twist the wire harness.

    3. Attach the clamp.

    4. B003JP0

      Install the harness clamp with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    5. Attach the clamp.

    6. B003QPW

      Install the 2 harness clamps with the 2 bolts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the clamps, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    7. Attach the clamp.

    8. B003PK6

      Attach the 2 clamps.

      Note

      When attaching the clamps, do not twist the wire harness.

    9. B003RVX

      Attach the 2 clamps.

      Note

      When attaching the clamps, do not twist the wire harness.

    10. Connect the connector and attach the clamp.

      Note


      • Do not attach the connector to the radiator fan shroud before connecting the connector.

      • Securely connect the connector.

    11. B003PYY

      for 1GD-FTV, 2GD-FTV:


      1. Install the upper arm heat insulator to the front suspension tower with the 2 bolts.

        Torque:
        25.5 N*m  { 260 kgf*cm, 19 ft.*lbf }

  3. INSTALL FRONT WHEEL

    Click here

  4. CHECK SPEED SENSOR SIGNAL

    Click here