ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | w/o Secondary Air Injection System | *B | w/ Secondary Air Injection System |
| *1 | AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | HOOD SUB-ASSEMBLY |
| *5 | INTAKE AIR CONNECTOR | *6 | NO. 1 AIR HOSE |
| *7 | NO. 2 PCV HOSE | *8 | VACUUM HOSE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Secondary Air Injection System | *B | w/o Secondary Air Injection System |
| *C | w/ Cover | - | - |
| *1 | FRONT FENDER SEAL LH | *2 | FRONT FENDER SEAL RH |
| *3 | FRONT UPPER FENDER APRON SEAL LH | *4 | FRONT UPPER FENDER APRON SEAL RH |
| *5 | NO. 1 ENGINE UNDER COVER ASSEMBLY | *6 | NO. 1 RADIATOR AIR GUIDE |
| *7 | NO. 2 ENGINE UNDER COVER | *8 | NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | w/ Secondary Air Injection System | *B | for Automatic Transmission |
| *1 | AIR PUMP INLET | *2 | FAN SHROUD |
| *3 | NO. 1 OIL COOLER INLET HOSE | *4 | NO. 1 OIL COOLER OUTLET HOSE |
| *5 | RADIATOR ASSEMBLY | *6 | RADIATOR HOSE INLET |
| *7 | RADIATOR HOSE OUTLET | *8 | RADIATOR RESERVOIR |
| *9 | RADIATOR DRAIN COCK PLUG | *10 | CLAMP |
| *11 | FAN AND GENERATOR V BELT | *12 | FAN PULLEY |
| *13 | FLUID COUPLING FAN | *14 | GROMMET |
| *15 | O-RING | *16 | WIRE HARNESS |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | ENGINE OIL LEVEL DIPSTICK |
| *3 | ENGINE OIL LEVEL DIPSTICK GUIDE | *4 | VANE PUMP ASSEMBLY |
| *5 | O-RING | *6 | STUD BOLT |
| *7 | HEATER WATER OUTLET HOSE | *8 | HEATER WATER INLET HOSE |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | STARTER ASSEMBLY | *2 | CLUTCH RELEASE CYLINDER ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for 4WD |
| *1 | ECM | *2 | ENGINE WIRE |
| *3 | GLOVE COMPARTMENT DOOR ASSEMBLY | *4 | NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RHD | *B | for 4WD |
| *1 | ECM | *2 | ENGINE WIRE |
| *3 | GLOVE COMPARTMENT DOOR ASSEMBLY | *4 | NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Secondary Air Injection System | *B | w/o Secondary Air Injection System |
| *C | for RHD | *D | for LHD |
| *1 | ENGINE WIRE | *2 | NO. 1 FUEL HOSE |
| *3 | NO. 2 FUEL HOSE | *4 | NO. 4 AIR INJECTION SYSTEM HOSE |
| *5 | PURGE LINE HOSE | *6 | UNION TO CONNECTOR TUBE HOSE |
| *7 | BATTERY | *8 | BATTERY HOLD DOWN CLAMP |
| *9 | POSITIVE BATTERY TERMINAL | *10 | BATTERY TRAY |
| *11 | ENGINE ROOM RELAY BLOCK | *12 | NO. 1 RELAY BLOCK COVER SIDE |
| *13 | NO. 1 RELAY BLOCK COVER UPPER | *14 | NO. 2 ENGINE WIRE |
| *15 | SENSOR BRACKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT AXLE HUB GREASE CAP LH | *2 | FRONT AXLE SHAFT NUT LH |
| *3 | FRONT DRIVE SHAFT ASSEMBLY LH | *4 | FRONT DRIVE SHAFT HOLE SNAP RING |
| *5 | FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH | *6 | FRONT SPEED SENSOR LH |
| *7 | TIE ROD END SUB-ASSEMBLY LH | *8 | LOCK CAP |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Differential oil |
 |
MP grease |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | POWER STEERING LINK ASSEMBLY | *2 | STEERING SLIDING YOKE |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | POWER STEERING LINK ASSEMBLY | *2 | STEERING SLIDING YOKE |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT DIFFERENTIAL CARRIER ASSEMBLY | *2 | FRONT DIFFERENTIAL BREATHER HOSE |
| *3 | FRONT NO. 1 DIFFERENTIAL SUPPORT | *4 | FRONT NO. 2 DIFFERENTIAL SUPPORT |
| *5 | FRONT NO. 3 DIFFERENTIAL SUPPORT | *6 | DIFFERENTIAL MOUNT NUT |
| *7 | UPPER DIFFERENTIAL MOUNT STOPPER | *8 | LOWER DIFFERENTIAL MOUNT STOPPER |
| *9 | DIFFERENTIAL BREATHER TUBE BRACKET | *10 | WIRE HARNESS |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for Pre-Runner | - | - |
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | PROPELLER SHAFT GUARD |
| *3 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY | *4 | COMPRESSION SPRING |
| *5 | EXHAUST PIPE SUPPORT | *6 | GASKET |
| *a | for Differential Type BD22 | *b | for Differential Type BD20 |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Do not apply lubricants |
ILLUSTRATION
| *A | for 4WD | *B | for TASA Made |
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | FRONT PROPELLER SHAFT ASSEMBLY |
| *3 | PROPELLER SHAFT GUARD | *4 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
| *5 | COMPRESSION SPRING | *6 | EXHAUST PIPE SUPPORT |
| *7 | GASKET | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Do not apply lubricants |
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | SHIFT LEVER KNOB SUB-ASSEMBLY | *2 | UPPER CONSOLE PANEL SUB-ASSEMBLY |
ILLUSTRATION
| *A | for R151 | - | - |
| *1 | MANUAL TRANSMISSION UNIT ASSEMBLY | *2 | GROUND CABLE |
| *3 | MANIFOLD STAY | *4 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *6 | SHIFT LEVER ASSEMBLY |
| *7 | SHIFT LEVER BOOT ASSEMBLY | *8 | WIRE HARNESS |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for R151F | - | - |
| *1 | MANUAL TRANSMISSION UNIT ASSEMBLY | *2 | GROUND CABLE |
| *3 | MANIFOLD STAY | *4 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *6 | SHIFT LEVER ASSEMBLY |
| *7 | SHIFT LEVER BOOT ASSEMBLY | *8 | WIRE HARNESS |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for AC60E | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | CLAMP |
| *3 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT | *4 | FLYWHEEL HOUSING DUST SEAL |
| *5 | GROUND CABLE | *6 | MANIFOLD STAY |
| *7 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY | *8 | OIL COOLER TUBE SUB-ASSEMBLY |
| *9 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *10 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *11 | WIRE HARNESS | *12 | TRANSMISSION INSULATOR RH |
| *13 | WIRE HARNESS CLAMP BRACKET | - | - |
| *a | Black: x 1 Silver: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for AC60F | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | CLAMP |
| *3 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT | *4 | FLYWHEEL HOUSING DUST SEAL |
| *5 | GROUND CABLE | *6 | MANIFOLD STAY |
| *7 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY | *8 | OIL COOLER TUBE SUB-ASSEMBLY |
| *9 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *10 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *11 | WIRE HARNESS | *12 | TRANSMISSION INSULATOR RH |
| *a | Black: x 1 Silver: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | CLUTCH COVER ASSEMBLY | *2 | CLUTCH DISC ASSEMBLY |
| *3 | ENGINE ASSEMBLY | *4 | FLYWHEEL SUB-ASSEMBLY |
| *5 | REAR END PLATE | *6 | FLYWHEEL HOUSING DUST SEAL |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
| *T1 | 1st: 26.5 (270, 20) 2nd: Turn 90° |
- | - |
ILLUSTRATION
| *A | for Automatic Transmission | - | - |
| *1 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *2 | REAR END PLATE |
| *3 | ENGINE ASSEMBLY | *4 | FRONT DRIVE PLATE SPACER |
| *5 | REAR DRIVE PLATE SPACER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | FRONT ENGINE MOUNTING HEAT INSULATOR RH | *2 | FRONT ENGINE MOUNTING INSULATOR |
| *3 | ENGINE HANGER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |