ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | HOOD SUB-ASSEMBLY | *2 | NO. 1 ENGINE UNDER COVER ASSEMBLY |
| *3 | NO. 2 ENGINE UNDER COVER | *4 | RADIATOR ASSEMBLY |
| *5 | RADIATOR RESERVE TANK ASSEMBLY | *6 | VANE PUMP OIL RESERVOIR ASSEMBLY |
| *7 | WASHER HOSE | *8 | FAN SHROUD |
| *9 | NO. 1 RADIATOR HOSE | *10 | NO. 2 RADIATOR HOSE |
| *11 | FLUID COUPLING ASSEMBLY | *12 | FAN PULLEY |
| *13 | FAN AND GENERATOR V BELT | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 1 INTAKE PIPE | *2 | NO. 1 AIR HOSE |
| *3 | NO. 2 AIR HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
ILLUSTRATION
| *1 | AIR CLEANER CAP AND HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | ENGINE WIRE |
| *5 | NO. 1 FUEL HOSE | *6 | NO. 2 FUEL HOSE |
| *7 | UNION TO CONNECTOR TUBE HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | BATTERY | *2 | BATTERY CLAMP SUB-ASSEMBLY |
| *3 | BATTERY TRAY | *4 | WATER HOSE SUB-ASSEMBLY |
| *5 | NO. 1 RELAY BLOCK UPPER | *6 | NO. 1 RELAY BLOCK SIDE |
| *7 | NO. 2 ENGINE WIRE | *8 | WIRE TO WIRE |
| *9 | ENGINE ROOM MAIN WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | PRESSURE FEED TUBE ASSEMBLY |
| *3 | UNION TO CONNECTOR TUBE HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | GASKET |
| *3 | COMPRESSION SPRING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY | *2 | DIFFERENTIAL TORSIONAL DAMPER |
| *3 | PROPELLER SHAFT GUARD | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
 |
Do not apply lubricants | - | - |
ILLUSTRATION
| *1 | UPPER CONSOLE PANEL ASSEMBLY | *2 | SHIFT LEVER KNOB SUB-ASSEMBLY |
| *3 | SHIFT LEVER BOOT ASSEMBLY | *4 | FLOOR SHIFT LEVER ASSEMBLY |
| *5 | CONSOLE BOX ASSEMBLY | - | - |
ILLUSTRATION
| *A | for RC61 | - | - |
| *1 | MANUAL TRANSMISSION UNIT ASSEMBLY | *2 | STIFFENER PLATE RH |
| *3 | STIFFENER PLATE LH | *4 | STARTER ASSEMBLY |
| *5 | CLUTCH RELEASE CYLINDER ASSEMBLY | *6 | REAR ENGINE MOUNTING INSULATOR |
| *7 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | CLUTCH COVER ASSEMBLY | *2 | CLUTCH DISC ASSEMBLY |
| *3 | FLYWHEEL SUB-ASSEMBLY | *4 | REAR END PLATE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 1 ENGINE HANGER UPPER | *2 | NO. 2 ENGINE HANGER |
| *3 | FRONT ENGINE MOUNTING INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |