ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | for Automatic Transmission | - | - |
| *1 | HOOD SUB-ASSEMBLY | *2 | NO. 1 ENGINE UNDER COVER ASSEMBLY |
| *3 | NO. 2 ENGINE UNDER COVER | *4 | RADIATOR ASSEMBLY |
| *5 | RADIATOR RESERVOIR | *6 | VANE PUMP OIL RESERVIOR ASSEMBLY |
| *7 | WASHER HOSE | *8 | FAN SHROUD |
| *9 | NO. 1 RADIATOR HOSE | *10 | NO. 2 RADIATOR HOSE |
| *11 | FLUID COUPLING ASSEMBLY | *12 | FAN PULLEY |
| *13 | FAN AND GENERATOR V BELT | *14 | NO. 1 OIL COOLER INLET HOSE |
| *15 | NO. 1 OIL COOLER OUTLET HOSE | *16 | OIL RESERVOIR BRACKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | INTERCOOLER ASSEMBLY | *2 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *3 | NO. 1 AIR HOSE | *4 | VACUUM HOSE |
| *5 | NO. 2 AIR HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE WIRE | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE WIRE | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | AIR CLEANER CAP AND HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | ENGINE WIRE |
| *5 | NO. 1 FUEL HOSE | *6 | NO. 2 FUEL HOSE |
| *7 | UNION TO CONNECTOR TUBE HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | BATTERY | *2 | BATTERY CLAMP SUB-ASSEMBLY |
| *3 | BATTERY TRAY | *4 | WATER HOSE SUB-ASSEMBLY |
| *5 | NO. 1 RELAY BLOCK UPPER | *6 | NO. 1 RELAY BLOCK SIDE |
| *7 | NO. 2 ENGINE WIRE | *8 | WIRE TO WIRE |
| *9 | ENGINE ROOM MAIN WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | PRESSURE FEED TUBE ASSEMBLY |
| *3 | UNION TO CONNECTOR TUBE HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | GASKET |
| *3 | COMPRESSION SPRING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FRONT PROPELLER SHAFT ASSEMBLY | *2 | PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
| *3 | TRANSFER CASE PROTECTOR LOWER | *4 | PROPELLER SHAFT GUARD |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
 |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | UPPER CONSOLE PANEL ASSEMBLY | *2 | SHIFT LEVER KNOB SUB-ASSEMBLY |
| *3 | SHIFT LEVER BOOT ASSEMBLY | *4 | FLOOR SHIFT LEVER ASSEMBLY |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | STEERING SLIDING YOKE | *2 | POWER STEERING LINK ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | STEERING SLIDING YOKE | *2 | POWER STEERING LINK ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | FRONT DIFFERENTIAL CARRIER ASSEMBLY | *2 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *3 | FRONT DRIVE SHAFT ASSEMBLY RH | *4 | FRONT PROPELLER SHAFT ASSEMBLY |
| *5 | OIL TEMPERATURE SENSOR | *6 | FRONT DIFFERENTIAL BREATHER HOSE |
| *7 | FRONT DRIVE SHAFT HOLE SNAP RING | *8 | FRONT NO. 1 DIFFERENTIAL SUPPORT |
| *9 | FRONT NO. 2 DIFFERENTIAL SUPPORT | *10 | FRONT NO. 3 DIFFERENTIAL SUPPORT |
| *11 | DIFFERENTIAL MOUNT NUT | *12 | UPPER DIFFERENTIAL MOUNT STOPPER |
| *13 | LOWER DIFFERENTIAL MOUNT STOPPER | *14 | DIFFERENTIAL BREATHER TUBE BRACKET |
| *15 | WIRE HARNESS | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part |  |
Differential oil |
 |
MP grease | |
Do not apply lubricants |
ILLUSTRATION
| *A | for Manual Transmission | - | - |
| *1 | MANUAL TRANSMISSION UNIT ASSEMBLY | *2 | STIFFENER PLATE RH |
| *3 | STIFFENER PLATE LH | *4 | STARTER ASSEMBLY |
| *5 | CLUTCH RELEASE CYLINDER ASSEMBLY | *6 | REAR ENGINE MOUNTING INSULATOR |
| *7 | NO. 3 FRAME CROSS MEMBER SUB-ASSEMBLY | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *A | for Automatic Transmission | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | DRIVE PLATE AND TORQUECONVERTER SETTING BOLT |
| *3 | OUTLET OIL COOLER TUBE | *4 | INLET OIL COOLER TUBE |
| *5 | STIFFNER PLATE RH | *6 | NO. 4 CYLINDER BLOCK INSULATOR |
| *7 | NO. 2 END PLATE | *8 | STIFFNER PLATE LH |
| *9 | STARTER ASSEMBLY | *10 | TRANSMISSION CONTROL CABLE BRACKET |
| *11 | REAR ENGINE MOUNTING INSULATOR | *12 | NO. 3 FRAME CROSS MEMBER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *A | for Automatic Transmission | *B | for Manual Transmission |
| *1 | CLUTCH COVER ASSEMBLY | *2 | CLUTCH DISC ASSEMBLY |
| *3 | FLYWHEEL SUB-ASSEMBLY | *4 | REAR END PLATE |
| *5 | PUMP IMPELLER DRIVE PLATE | *6 | REAR DRIVE PLATE SPACER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE HANGER | *2 | ENGINE HANGER |
| *3 | FRONT ENGINE MOUNTING INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |