ЖИДКОСТЬ ДЛЯ АВТОМАТИЧЕСКОЙ ТРАНСМИССИИ ЗАМЕНА

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after automatic transmission fluid replacement are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly

Click here

PROCEDURE


  1. REPLACE AUTOMATIC TRANSMISSION FLUID


    1. Lift the vehicle. [*1]

      Note

      Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).

    2. A01LDU8C04
      *1 Drain Plug
      *2 Overflow Plug
      *3 Refill Plug
      *4 O-ring

      Remove the drain plug and gasket from the automatic transmission assembly to drain the automatic transmission fluid. [*2]

    3. Temporarily install the gasket and drain plug to the automatic transmission assembly. [*3]

      Tech Tips

      Reuse the old gasket as the drain plug will be removed again.

    4. Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly. [*4]

    5. Remove the refill plug and O-ring from the automatic transmission assembly. [*5]

    6. Add automatic transmission fluid to the refill hole until it flows out of the overflow hole. [*6]

      A01LEMEC01
      *a Refill Hole *b Overflow Hole

      Note


      • Use Toyota Genuine ATF WS.

      • Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.

    7. Wait until the automatic transmission fluid flow slows and only drops come out. [*7]

      A01LASG

    8. Using a 5 mm hexagon socket wrench. temporarily install the gasket and overflow plug to the automatic transmission assembly. [*8]

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again.

    9. Add the amount of the automatic transmission fluid specified for removal and installation of the automatic transmission oil pan sub-assembly to the refill hole. [*9]

      Specified Amount of Fluid
      1.7 liters (1.8 US qts, 1.5 Imp. qts)

      Tech Tips

      if the specified amount of the automatic transmission fluid cannot be added, perform steps [*10] to [*14].

    10. Temporarily install the O-ring and refill plug to the automatic transmission assembly. [*10]

      Tech Tips

      Reuse the old O-ring as the refill plug will be removed again.

    11. Lower the vehicle. [*11]

    12. Start the engine. [*12]

      Note

      To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.

    13. Slowly move the shift lever from P to D, and then move the shift lever to P. [*13]

    14. Allow the engine to idle for 30 seconds to warm it up. [*14]

    15. Turn the ignition switch off. [*15]

    16. Repeat steps [*1] to [*15].

    17. Repeat steps [*1] to [*2].

    18. Install a new gasket and the drain plug to the automatic transmission assembly. [*16]

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    19. Repeat steps [*4] to [*11].

  2. ADJUST FLUID TEMPERATURE

    Click here

  3. CHECK FLUID LEVEL

    Click here

  4. AFTER FILLING TRANSMISSION

    Click here

  5. ATF THERMAL DEGRADATION ESTIMATE RESET

    Click here