БЛОК ДВИГАТЕЛЯ РАЗБОРКА

PROCEDURE


  1. REMOVE SPARK PLUG

    Click here

  2. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

    Click here

  3. REMOVE KNOCK SENSOR

    Click here

  4. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

    Click here

  5. REMOVE OIL FILLER CAP SUB-ASSEMBLY


    1. Remove the oil filler cap.

    2. Remove the gasket from the oil filler cap sub-assembly.

  6. REMOVE PCV VALVE SUB-ASSEMBLY

    Click here

  7. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

    Click here

  8. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

    Click here

  9. REMOVE CRANKSHAFT POSITION SENSOR

    Click here

  10. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

    Click here

  11. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

    Click here

  12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  13. REMOVE NO. 1 VENTILATION CONNECTOR


    1. A01SBW5

      Remove the 2 bolts and No. 1 ventilation connector from the cylinder head cover sub-assembly.

  14. REMOVE WATER INLET

    Click here

  15. REMOVE THERMOSTAT

    Click here

  16. REMOVE CRANKSHAFT PULLEY

    Click here

  17. REMOVE OIL PAN COVER SILENCER

    Click here

  18. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

    Click here

  19. REMOVE OIL STRAINER SUB-ASSEMBLY

    Click here

  20. REMOVE OIL PAN SUB-ASSEMBLY

    Click here

  21. REMOVE OIL PAN STUD BOLT

    Note

    If an oil pan stud bolt is deformed or its threads are damaged, replace it.

  22. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

  23. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

    Click here

  24. REMOVE ENGINE WATER PUMP ASSEMBLY

    Click here

  25. REMOVE TIMING CHAIN CASE OIL SEAL

    Click here

  26. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    1. B00276EC01
      *1 Crankshaft Pulley Set Key
      *a Timing Mark
      *b Approximately 13°
      *c Approximately 30°

      Temporarily install the crankshaft pulley bolt.

    2. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

      Tech Tips

      If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.

    3. Remove the crankshaft pulley bolt.

  27. REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY


    1. A01SARE

      Remove the 2 bolts and cylinder head cover connector sub-assembly.

    2. Remove the No. 2 camshaft bearing cap oil hole gasket and 3 No. 3 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.

  28. REMOVE TIMING CHAIN GUIDE


    1. B0027A9C01
      *1 O-Ring

      Remove the 2 bolts, timing chain guide and O-ring.

  29. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

    Note


    • When the No. 1 chain tensioner assembly is removed, do not rotate the crankshaft.

    • When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

    B0027HGC25
    *a Plunger
    *b Stopper Plate
    *c Hexagon Wrench

    1. Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.

    2. Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.

    3. B0028JC

      Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.

  30. REMOVE CHAIN TENSIONER SLIPPER


    1. A01SDEG

      Remove the bolt and chain tensioner slipper.

  31. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    1. A01SBSD

      Remove the bolt, nut and No. 1 chain vibration damper.

  32. REMOVE CHAIN SUB-ASSEMBLY

  33. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET


    1. A01W8F5

      Remove the crankshaft timing gear or sprocket from the crankshaft.

  34. REMOVE CAMSHAFT BEARING CAP

    Click here

  35. REMOVE CAMSHAFT

    Click here

  36. REMOVE NO. 2 CAMSHAFT

    Click here

  37. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    Click here

  38. REMOVE VALVE LASH ADJUSTER ASSEMBLY

    Click here

  39. REMOVE VALVE STEM CAP

    Click here

  40. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

    Click here

  41. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

    Click here

  42. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

    Click here

  43. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

    Click here

  44. REMOVE CYLINDER HEAD SUB-ASSEMBLY

    Click here

  45. REMOVE CYLINDER HEAD GASKET

    Click here

  46. REMOVE OIL CONTROL VALVE FILTER


    1. A01SCYD

      Using an 8 mm hexagon wrench, remove the screw plug.

    2. Remove the oil control valve filter and gasket.

  47. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    1. B0026ISC09
      *a Plunger
      *b Stopper Plate
      *c Hexagon Wrench

      Move the stopper plate downward to release the lock and push the plunger deep into the No. 2 chain tensioner assembly.

    2. Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.

    3. A01SDZY

      Remove the bolt and No. 2 chain vibration damper.

  48. REMOVE NO. 3 CHAIN VIBRATION DAMPER


    1. A01SDHM

      Remove the 2 bolts and No. 3 chain vibration damper.

  49. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    1. A01SB4A

      Remove the hexagon wrench from the No. 2 chain tensioner assembly.

    2. Remove the nut and No. 2 chain tensioner assembly.

  50. REMOVE NO. 2 CHAIN SUB-ASSEMBLY


    1. A01SDXV

      Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.

    2. Remove the No. 2 crankshaft timing sprocket and No. 2 chain sub-assembly.

  51. REMOVE NO. 4 CHAIN VIBRATION DAMPER


    1. A01SEHH

      Remove the 2 bolts and No. 4 chain vibration damper.

  52. REMOVE CRANKSHAFT PULLEY SET KEY


    1. A01SEZG

      Remove the 2 crankshaft pulley set keys from the crankshaft.

  53. REMOVE NO. 4 WATER BY-PASS PIPE (w/ Oil Cooler)


    1. A01SB2L

      Disconnect the No. 5 water by-pass hose from the oil cooler assembly.

    2. Remove the 2 bolts and No. 4 water by-pass pipe.

  54. REMOVE NO. 4 WATER BY-PASS HOSE (w/ Oil Cooler)


    1. A01SBRX

      Slide the 2 clips and remove the No. 4 water by-pass hose from the oil cooler assembly and union.

  55. REMOVE OIL FILTER SUB-ASSEMBLY

    Click here

  56. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

    Click here

  57. REMOVE OIL FILTER UNION (w/o Oil Cooler)


    1. A01SA8I

      Using a 27 mm socket wrench, remove the oil filter union.

  58. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    1. A01SEBH

      Remove the 2 bolts and nut from the oil filter bracket.

    2. Remove the 2 screw plugs and 2 gaskets from the oil filter bracket sub-assembly.

    3. B00247XC01
      *1 O-Ring
      *2 Oil Filter Bracket Gasket

      Remove the oil filter bracket gasket and O-ring.

    4. A01SD4S

      Using a hexagon wrench, remove the oil filter bracket union.

  59. REMOVE UNION (w/ Oil Cooler)


    1. A01SDBW

      Remove the union from the cylinder block sub-assembly.

  60. REMOVE NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)


    1. A01SDMU

      Remove the No. 1 taper screw plug from the cylinder block sub-assembly.

  61. REMOVE REAR ENGINE OIL SEAL RETAINER


    1. Remove the 6 bolts.

    2. B002635C01
      *a Protective Tape

      Using a screwdriver with its tip taped, pry out the rear engine oil seal retainer.

      Note

      Be careful not to damage the contact surfaces of the cylinder block sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  62. REMOVE REAR ENGINE OIL SEAL


    1. B0025EXC01
      *a Protective Tape
      *b Wooden Blocks

      Place the rear engine oil seal retainer on wooden blocks.

    2. Using a screwdriver with its tip taped and a hammer, tap out the rear engine oil seal.

      Tech Tips

      Tape the screwdriver tip before use.