ДВИГАТЕЛЬ В СБОРЕ УЗЛЫ И ДЕТАЛИ
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | HOOD SUB-ASSEMBLY |
| *5 | INTAKE AIR CONNECTOR | *6 | NO. 1 AIR HOSE |
| *7 | NO. 2 PCV HOSE | *8 | VACUUM HOSE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT FENDER SEAL LH | *2 | FRONT FENDER SEAL RH |
| *3 | FRONT UPPER FENDER APRON SEAL LH | *4 | FRONT UPPER FENDER APRON SEAL RH |
| *5 | NO. 1 RADIATOR AIR GUIDE | - | - |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | w/ Cover | - | - |
| *1 | FAN SHROUD | *2 | NO. 1 ENGINE UNDER COVER |
| *3 | NO. 1 ENGINE UNDER COVER ASSEMBLY | *4 | RADIATOR ASSEMBLY |
| *5 | RADIATOR HOSE INLET | *6 | RADIATOR HOSE OUTLET |
| *7 | RADIATOR RESERVOIR | *8 | RADIATOR DRAIN COCK PLUG |
| *9 | FAN AND GENERATOR V BELT | *10 | FAN PULLEY |
| *11 | FLUID COUPLING FAN | *12 | GROMMET |
| *13 | O-RING | *14 | WIRE HARNESS |
| *15 | CLAMP | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | w/ Air Conditioning System | - | - |
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | ENGINE OIL LEVEL DIPSTICK |
| *3 | ENGINE OIL LEVEL DIPSTICK GUIDE | *4 | HEATER WATER OUTLE HOSE |
| *5 | HEATER WATER INLET HOSE | *6 | STARTER ASSEMBLY |
| *7 | VANE PUMP ASSEMBLY | *8 | CLUTCH RELEASE CYLINDER ASSEMBLY |
| *9 | O-RING | *10 | STUD BOLT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ECM | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
| *3 | ENGINE WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ECM | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
| *3 | ENGINE WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | NO. 1 FUEL HOSE | *2 | NO. 2 FUEL HOSE |
| *3 | PURGE LINE HOSE | *4 | UNION TO CONNECTOR TUBE HOSE |
| *5 | BATTERY | *6 | BATTERY HOLD DOWN CLAMP |
| *7 | BATTERY POSITIVE TERMINAL | *8 | BATTERY TRAY |
| *9 | ENGINE ROOM RELAY BLOCK | *10 | NO. 1 RELAY BLOCK COVER SIDE |
| *11 | NO. 1 RELAY BLOCK COVER UPPER | *12 | ENGINE WIRE |
| *13 | NO. 2 ENGINE WIRE | *14 | SENSOR BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | PROPELLER SHAFT GUARD |
| *3 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY | *4 | COMPRESSION SPRING |
| *5 | EXHAUST PIPE SUPPORT | *6 | GASKET |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Do not apply lubricants |
ILLUSTRATION
| *A | w/ Rear Console Box | - | - |
| *1 | CONSOLE BOX CARPET | *2 | SHIFT LEVER KNOB SUB-ASSEMBLY |
| *3 | FRONT CONSOLE BOX SUB-ASSEMBLY | *4 | REAR CONSOLE BOX SUB-ASSEMBLY |
| *5 | SHIFT LEVER KNOB SUB-ASSEMBLY | - | - |
ILLUSTRATION
| *1 | MANUAL TRANSMISSION UNIT ASSEMBLY | *2 | GROUND CABLE |
| *3 | MANIFOLD STAY | *4 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *6 | SHIFT LEVER ASSEMBLY |
| *7 | SHIFT LEVER BOOT ASSEMBLY | *8 | WIRE HARNESS |
| *9 | NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | CLUTCH COVER ASSEMBLY | *2 | CLUTCH DISC ASSEMBLY |
| *3 | ENGINE ASSEMBLY | *4 | FLYWHEEL SUB-ASSEMBLY |
| *5 | REAR END PLATE | *6 | FLYWHEEL HOUSING DUST SEAL |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
| *T1 | 1st: 26.5 (270, 20) 2nd: Turn 90° |
- | - |
ILLUSTRATION
| *1 | ENGINE HANGER | *2 | FRONT ENGINE MOUNTING HEAT INSULATOR RH |
| *3 | FRONT ENGINE MOUNTING INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |