БЛОК ДВИГАТЕЛЯ УСТАНОВКА

PROCEDURE


  1. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

    Click here

  2. INSTALL OIL FILTER SUB-ASSEMBLY

    Click here

  3. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

    Click here

  4. INSTALL EXHAUST MANIFOLD

    Click here

  5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  6. INSTALL VACUUM PUMP OIL OUTLET HOSE


    1. Install the vacuum pump oil outlet hose to the oil pan sub-assembly and slide the clip to secure the hose.

  7. INSTALL UNION


    1. Clean the threads of the union and hole.

    2. Apply adhesive to 2 or 3 threads at the end of union.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    3. Install the union to the cylinder block sub-assembly.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  8. INSTALL VACUUM PUMP OIL INLET HOSE

    Click here

  9. INSTALL PUMP BRACKET


    1. B0026EFN01

      Install the pump bracket with the 6 bolts.

      Torque:
      for bolt A
      57 N*m  { 581 kgf*cm, 42 ft.*lbf }
      for bolt B
      78 N*m  { 795 kgf*cm, 58 ft.*lbf }
      Bolt Length
      Item Length Thread Diameter
      Bolt A 26 mm (1.02 in.) 18 mm (0.709 in.)
      Bolt B 29 mm (1.14 in.) 19 mm (0.748 in.)

  10. INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH


    1. Install the No. 1 front engine mounting bracket RH with the 4 bolts.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

  11. INSTALL WATER HOSE JOINT


    1. Clean the threads of the water hose joint and hole.

    2. Apply adhesive to 2 or 3 threads at the end of the water hose joint.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    3. B0026T7C01
      *a LH Side

      Install the water hose joint.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Note

      Install the water hose joint within 3 minutes after applying adhesive.

    4. Rotate the water hose joint clockwise to the position shown in the illustration.

      Note


      • Do not rotate the water hose joint by more than 1 revolution (360°) after tightening the water hose joint to the specified torque.

      • Do not loosen the water hose joint after setting it correctly.

  12. INSTALL WATER OUTLET HOUSING


    1. Install a new gasket to the cylinder head sub-assembly.

    2. Install the water outlet hosing with the 3 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  13. INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)


    1. Temporarily install the idle pulley assembly with bracket with the 3 bolts.

    2. Tighten the 3 bolts.

      Torque:
      46.6 N*m  { 475 kgf*cm, 34 ft.*lbf }

  14. INSTALL INTAKE MANIFOLD

    Click here

  15. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  16. INSTALL CRANKSHAFT POSITION SENSOR

    Click here

  17. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

    Click here

  18. INSTALL INJECTION PUMP ASSEMBLY

    Click here

  19. INSTALL INJECTION PUMP DRIVE PULLEY

    Click here

  20. INSTALL GLOW PLUG ASSEMBLY

    Click here

  21. INSTALL NOZZLE HOLDER AND NOZZLE SET

    Click here

  22. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

    Click here

  23. INSTALL NO. 1 GLOW PLUG CONNECTOR

    Click here

  24. INSTALL INJECTION PIPE SUB-ASSEMBLY

    Click here

  25. INSTALL VENTURI ASSEMBLY

    Click here

  26. INSTALL INTAKE FLANGE

    Click here

  27. INSTALL CRANKSHAFT TIMING PULLEY

    Click here

  28. INSTALL TIMING BELT GUIDE

    Click here

  29. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  30. INSTALL TIMING BELT

    Click here

  31. INSTALL TIMING BELT COVER

    Click here

  32. INSTALL CRANKSHAFT PULLEY

    Click here

  33. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)


    1. Install the No. 1 compressor mounting bracket with the 4 bolts.

      Torque:
      85.9 N*m  { 876 kgf*cm, 63 ft.*lbf }