BLACK OUT TAPE REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 black out tape and No. 2 black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Fully open the front door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE LOWER DOOR FRAME GARNISH LH

    Click here

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE FRONT ARMREST ASSEMBLY LH

    Click here

  8. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  12. REMOVE FRONT DOOR GLASS RUN LH

    Click here

  13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  14. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  15. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Click here

  16. REMOVE FRONT DOOR WEATHERSTRIP LH

    Click here

  17. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH (w/ Upper Window Frame Moulding)

    Click here

  18. REMOVE NO. 2 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 2 black out tape LH, heat the front door panel and No. 2 black out tape LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    No. 2 Black Out Tape LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006L2EC23
    *a Heated Part
    *b Heat Light

    1. B006R35

      Pull back an edge of the No. 2 black out tape LH and pull it parallel to the front door panel to remove it.

  19. REMOVE NO. 1 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 1 black out tape LH, heat the front door panel and No. 1 black out tape LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    No. 1 Black Out Tape LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006L2EC23
    *a Heated Part
    *b Heat Light

    1. B006OHA

      Pull back an edge of the No. 1 black out tape LH and pull it parallel to the front door panel to remove it.