FRONT DOOR WINDOW FRAME MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH (w/ Upper Window Frame Moulding)


    1. Install the front door upper window frame moulding LH.

    2. Install a nose piece to an air riveter or hand riveter.

    3. Insert the mandrel part of a new rivet into the nose piece.

    4. Placing the riveter upright against the front door upper window frame moulding LH, install the 5 rivets from the front of vehicle and moving toward the rear.

      B006R98

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • B006O68C27
        *1 Riveter
        *2 Mandrel
        *a INCORRECT
        *b CORRECT

        Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

      • B006PE4C28
        *1 Riveter
        *a INCORRECT
        *b CORRECT

        Confirm that the rivets are seated properly against the front door upper window frame moulding LH.

      • Do not tilt the riveter when installing the rivet to the front door upper window frame moulding LH.

      • Do not leave any space between the rivet head and front door upper window frame moulding LH.

      • B006OZJC27
        *1 Riveter
        *a INCORRECT
        *b CORRECT

        Do not leave any space between the front door upper window frame moulding LH and front door panel. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL FRONT DOOR WEATHERSTRIP LH


    1. B006QQD

      w/ Upper Window Frame Moulding:

      Attach the clip to install the front door weatherstrip LH.

    2. B006OTW

      w/o Upper Window Frame Moulding:

      Attach the clip to install the front door weatherstrip LH.

  3. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Tech Tips

    When installing the front door rear window frame moulding LH, heat the front door panel and front door rear window frame moulding LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Rear Window Frame Moulding LH 20 to 30°C (68 to 86°F)

    1. Clean the front door panel surface.


      1. Using a heat light, heat the front door panel surface.

      2. Remove the double-sided tape from the front door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new front door rear window frame moulding LH.


      1. Using a heat light, heat a new front door rear window frame moulding LH and the front door panel surface.

      2. Remove the peeling paper from the face of the front door rear window frame moulding LH.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. B006RIRC02
        *a Double-sided Tape
        *b Caulking Sponge with Butyl Layer
        B006N8A Install in this Direction

        Attach the clip to install the front door rear window frame moulding LH as shown in the illustration.

        Tech Tips

        Press the front door rear window frame moulding LH firmly to install it.

  4. INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING LH

    Tech Tips

    When installing the front door front window frame moulding LH, heat the front door panel and front door front window frame moulding LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Front Window Frame Moulding LH 20 to 30°C (68 to 86°F)

    1. Clean the front door panel surface.


      1. Using a heat light, heat the front door panel surface.

      2. Remove the double-sided tape from the front door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new front door front window frame moulding LH.


      1. Using a heat light, heat a new front door front window frame moulding LH and the front door panel surface.

      2. Remove the peeling paper from the face of the front door front window frame moulding LH.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. B006MX6C02
        *a Double-sided Tape
        *b Caulking Sponge with Butyl Layer
        B006N8A Install in this Direction (1)
        B006NJK Install in this Direction (2)

        Attach the clip to install the front door front window frame moulding LH as shown in the illustration.

        Tech Tips

        Press the front door front window frame moulding LH firmly to install it.

  5. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  6. INSTALL FRONT DOOR GLASS RUN LH

    Click here

  7. INSTALL FRONT DOOR SERVICE HOLE COVER LH

    Click here

  8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  10. INSTALL COURTESY LIGHT ASSEMBLY

    Click here

  11. INSTALL FRONT ARMREST ASSEMBLY LH

    Click here

  12. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    Click here

  13. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    Click here

  14. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  15. INSTALL LOWER DOOR FRAME GARNISH LH

    Click here

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  17. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  18. CHECK POWER WINDOW CONTROL SYSTEM

    Click here