FRONT DOOR BELT MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door outer glass weatherstrip removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and Start System (for 2AR-FE)

Click here

Stop and Start System (for 2GR-FKS)

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Fully open the front door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE LOWER DOOR FRAME GARNISH LH

    Click here

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE FRONT ARMREST ASSEMBLY LH

    Click here

  8. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  12. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Click here

  13. REMOVE FRONT DOOR GLASS RUN LH

    Click here

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  15. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP LH


    1. B006Q4ZC02
      B006PCE Protective Tape

      Put protective tape around the front door outer glass weatherstrip LH.

    2. B006PIG

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw from the interior.

    3. B006PS5C02
      B006N8A Remove in this Direction

      Detach the claw as shown in the illustration.

    4. B006MC8C01
      B006N8A Remove in this Direction

      Remove the front door outer glass weatherstrip LH as shown in the illustration.