FRONT DOOR WINDOW FRAME MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door front window frame moulding LH, front door rear window frame moulding LH and front door upper window frame moulding LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and Start System (for 2AR-FE)

Click here

Stop and Start System (for 2GR-FKS)

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Fully open the front door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE LOWER DOOR FRAME GARNISH LH

    Click here

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  7. REMOVE FRONT ARMREST ASSEMBLY LH

    Click here

  8. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  12. REMOVE FRONT DOOR GLASS RUN LH

    Click here

  13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  14. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH

    Tech Tips

    When removing front door front window frame moulding LH, heat the front door panel and front door front window frame moulding LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Front Window Frame Moulding LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006L2EC23
    *a Heated Part
    *b Heat Light

    1. B006OQWC02
      B006PCE Protective Tape

      Put protective tape around the front door front window frame moulding LH.

    2. B006Q4PC03
      *a Double-sided Tape
      *b Caulking Sponge with Butyl Layer

      Using a scraper, start from the top and remove the double-sided tape from the back of the front door front window frame moulding LH.

    3. B006LILC05
      B006N8A Remove in this Direction (1)
      B006NJK Remove in this Direction (2)

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip and remove the front door front window frame moulding LH.

  15. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Tech Tips

    When removing front door rear window frame moulding LH, heat the front door panel and front door rear window frame moulding LH using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Rear Window Frame Moulding LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B006L2EC23
    *a Heated Part
    *b Heat Light

    1. B006MFPC02
      B006PCE Protective Tape

      Put protective tape around the front door rear window frame moulding LH.

    2. B006MWCC03
      *a Double-sided Tape
      *b Caulking Sponge with Butyl Layer

      Using a scraper, start from the top and remove the double-sided tape from the back of the front door rear window frame moulding LH.

    3. B006NM6C03
      B006N8A Remove in this Direction

      Detach the clip and remove the front door rear window frame moulding LH as shown in the illustration.

  16. REMOVE FRONT DOOR WEATHERSTRIP LH


    1. B006QQD

      w/ Upper Window Frame Moulding:

      Using a clip remover, detach the clip and remove enough of the upper portion of the front door weatherstrip LH so that the front door upper window frame moulding LH can be removed.

    2. B006OTW

      w/o Upper Window Frame Moulding:

      Using a clip remover, detach the clip and remove enough of the upper portion of the front door weatherstrip LH so that the front door upper window frame moulding LH can be removed.

  17. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH (w/ Upper Window Frame Moulding)


    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

      Tech Tips

      Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the 5 rivets and drill off the flanges of the 5 rivets.

      B006NTGN03
      Standard
      Area Specified Condition
      A 5 mm (0.197 in.)

      CAUTION:

      Be careful of the drilled rivet as it may become hot.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

    4. Remove the front door upper window frame moulding LH.

    5. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.