HEADLIGHT DIMMER SWITCH INSPECTION

PROCEDURE


  1. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for Headlight Dimmer Switch LH Side Type)


    1. Inspect the light control switch.


      1. A01UDF4C53
        *a

        Component without harness connected

        (Headlight Dimmer Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G113-18(T) - G113-15(EL) Light control switch off 10 kΩ or higher
        G113-20(A) - G113-15(EL)
        G113-19(H) - G113-15(EL)
        G113-18(T) - G113-15(EL) Light control switch tail position Below 1 Ω
        G113-19(H) - G113-15(EL) Light control switch head position Below 1 Ω
        G113-18(T) - G113-15(EL)
        G113-20(A) - G113-15(EL) Light control switch AUTO position Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.

    2. A01UDF4C54
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the headlight dimmer switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G113-17(HF) - G113-15(EL) Headlight dimmer switch flash position Below 1 Ω
        G113-14(HU) - G113-15(EL)
        G113-14(HU) - G113-15(EL) Headlight dimmer switch high position Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.

    3. A01UDF4C55
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the turn signal light switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G113-12(TR) - G113-15(EL) Turn signal switch neutral position 10 kΩ or higher
        G113-11(TL) - G113-15(EL)
        G113-13(CR) - G113-15(EL)
        G113-12(TR) - G113-15(EL)

        Turn signal switch right turn position

        (self cancel condition)

        		 Below 1 Ω
        G113-12(TR) - G113-15(EL)

        Turn signal switch right turn position

        (cancel ratchet operation condition)

        		 Below 1 Ω
        G113-12(TR) - G113-13(CR)
        G113-13(CR) - G113-15(EL)
        G113-11(TL) - G113-15(EL)

        Turn signal switch left turn position

        (self cancel condition)

        		 Below 1 Ω
        G113-11(TL) - G113-15(EL)

        Turn signal switch left turn position

        (cancel ratchet operation condition)

        		 Below 1 Ω
        G113-11(TL) - G113-13(CR)
        G113-13(CR) - G113-15(EL)

        Tech Tips


        • The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).

        • The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch operation is 12°).

        If the result is not as specified, replace the headlight dimmer switch assembly.

    4. A01UDF4C56
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the front fog light switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G113-9(BFG) - G113-8(LFG) Front fog light switch off 10 kΩ or higher
        G113-9(BFG) - G113-8(LFG) Front fog light switch on Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.

    5. A01UDF4C58
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      w/ Rear Fog Light:

      Inspect the rear fog light switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G113-9(BFG) - G113-8(LFG) Rear fog light switch off 10 kΩ or higher
        G113-7(B) - G113-8(LFG)
        G113-9(BFG) - G113-8(LFG) Rear fog light switch on Below 1 Ω
        G113-7(B) - G113-8(LFG)

        If the result is not as specified, replace the headlight dimmer switch assembly.

  2. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for Headlight Dimmer Switch RH Side Type)


    1. Inspect the light control switch.


      1. A01UDF4C48
        *a

        Component without harness connected

        (Headlight Dimmer Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G2-13(T) - G2-16(EL) Light control switch off 10 kΩ or higher
        G2-11(A) - G2-16(EL)
        G2-12(H) - G2-16(EL)
        G2-13(T) - G2-16(EL) Light control switch tail position Below 1 Ω
        G2-12(H) - G2-16(EL) Light control switch head position Below 1 Ω
        G2-13(T) - G2-16(EL)
        G2-11(A) - G2-16(EL) Light control switch AUTO position Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.

    2. A01UDF4C49
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the headlight dimmer switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G2-14(HF) - G2-16(EL) Headlight dimmer switch flash position Below 1 Ω
        G2-17(HU) - G2-16(EL)
        G2-17(HU) - G2-16(EL) Headlight dimmer switch high position Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.

    3. A01UDF4C50
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the turn signal light switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G2-20(TR) - G2-16(EL) Turn signal switch neutral position 10 kΩ or higher
        G2-19(TL) - G2-16(EL)
        G2-18(CR) - G2-16(EL)
        G2-20(TR) - G2-16(EL)

        Turn signal switch right turn position

        (self cancel condition)

        		 Below 1 Ω
        G2-20(TR) - G2-16(EL)

        Turn signal switch right turn position

        (cancel ratchet operation condition)

        		 Below 1 Ω
        G2-20(TR) - G2-18(CR)
        G2-18(CR) - G2-16(EL)
        G2-19(TL) - G2-16(EL)

        Turn signal switch left turn position

        (self cancel condition)

        		 Below 1 Ω
        G2-19(TL) - G2-16(EL)

        Turn signal switch left turn position

        (cancel ratchet operation condition)

        		 Below 1 Ω
        G2-19(TL) - G2-18(CR)
        G2-18(CR) - G2-16(EL)

        Tech Tips


        • The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).

        • The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch operation is 12°).

        If the result is not as specified, replace the headlight dimmer switch assembly.

    4. A01UDF4C51
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Inspect the front fog light switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        G2-2(BFG) - G2-3(LFG) Front fog light switch off 10 kΩ or higher
        G2-2(BFG) - G2-3(LFG) Front fog light switch on Below 1 Ω

        If the result is not as specified, replace the headlight dimmer switch assembly.