HEADLIGHT ASSEMBLY(for VELLFIRE) REASSEMBLY

CAUTION / NOTICE / HINT

Note


  • Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

  • Do not reuse parts which have reduced fastening ability due to thread damage.

  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

  • When installing components, make sure that the wire harness is not pinched or pulled.

  • Do not use solvent to clean components. Only clean them with a dry cloth.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL HEADLIGHT LED UNIT ASSEMBLY LH

    Note


    • Prevention of static electricity is required during this procedure.

    • Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

    • Perform work using clean rubber gloves.

    • Do not touch the headlight LED unit assembly LH with bare hands.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wipe with a soft cloth.

    • If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.

    SST
    09890-47010   ( 09891-04020, 09891-04010, 09891-04030, 09891-04040 )

    1. B006KNVC01
      *a Rail

      Set the headlight LED unit assembly LH onto the left and right rails and aiming screws for beam axis vertical and horizontal adjustments.

      Tech Tips

      Set it into place by aligning the arrows shown in the illustration: black with black, and white with white.

    2. B006LZQC01
      B006N8A Clockwise

      Hold the headlight LED unit assembly LH with one hand to prevent it from tipping over and tighten the aiming screws for beam axis horizontal and vertical adjustments clockwise with the number of turns that were recorded.

    3. B006LIRC01
      B006Q1Z Push Here

      Push the part shown in the illustration to connect the pivot collar.

    4. B006LZQC01
      B006N8A Clockwise

      Tighten the aiming screws for beam axis horizontal and vertical adjustments by rotating them clockwise 10 times each.

    5. B006MM2

      Connect the 2 connectors.

  2. INSTALL HEADLIGHT CLEARANCE LED UNIT LH

    Note


    • Prevention of static electricity is required during this procedure.

    • Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

    • Perform work using clean rubber gloves.

    • Do not touch the No. 1 headlight clearance LED unit LH with bare hands.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wipe with a soft cloth.

    • If there are fingerprints on the inner surface of the lens, lightly wipe with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.

    SST
    09890-47010   ( 09891-04020, 09891-04010, 09891-04030, 09891-04040 )

    1. B006R2I

      Install the No. 1 headlight clearance LED unit LH with the 5 screws.

    2. Connect the connector and attach the wire harness clamp.

  3. INSTALL HEADLIGHT LENS GASKET

    Note


    • The headlight lens gasket must not be reused.

    • Perform work using clean rubber gloves.

    • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • If there are fingerprints on the inner surface of the lens, lightly wipe with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.


    1. B006P1PC01
      B006PCE Area to Clean

      Clean the headlight lens gasket installation groove.

    2. Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

      Tech Tips

      Use the peeling paper that is supplied with the headlight lens gasket.

    3. B006NHR

      Using scissors, cut the headlight lens gasket at a 90°.

    4. B006PMEC01
      B006REU Starting Point
      B006N8A Clockwise

      Starting from the position shown in the illustration, set the headlight lens gasket into the straight groove clockwise until it meets the corner groove.

      Note

      Lightly set the gasket in place without pulling.

    5. Fold the peeling paper over the tip of a screwdriver and fix it in place with tape.

      Note

      Use the peeling paper that is supplied with the seal.

    6. B006KW3C01
      B006LKF Corner Groove
      B006NAX Headlight Lens Gasket
      B006PCE Peeling Paper

      Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

      Note


      • Lightly set the gasket in place without pulling.

      • If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.

    7. Repeat the following order while working in a circle back to the starting point.


      1. Set headlight lens gasket into straight groove.

      2. Push into bottom of groove.

      3. Set into corner groove.

      4. Push into bottom of groove.

    8. B006LCBC01
      *a 20 mm (0.7874 in.)
      B006LKF Corner Groove

      Using scissors, cut the headlight lens gasket at a 45° angle at the starting point so that the gasket overlaps itself 20 mm (0.7874 in.) and set the gasket in place.

    9. Check the installation condition of the headlight lens gasket.

      OK
      Gasket not pushed up or protruding.
      No gap where gasket overlaps.

      Note

      Check the corners carefully since the gasket can easily become pushed up in those areas.

  4. INSTALL HEADLIGHT LENS LH

    Note


    • Prevention of static electricity is required during this procedure.

    • Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

    • Perform work using clean rubber gloves.

    • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.

    SST
    09890-47010   ( 09891-04010, 09891-04020, 09891-04030, 09891-04040 )

    1. B006PLXC01
      B006PCE Area to Clean

      Clean the headlight lens gasket contact surface.

    2. Set the headlight lens LH in place.

      Note

      B006NIQC01
      B006N7C Headlight Lens Gasket
      B006NAX Headlight Housing
      B006PCE Headlight Lens LH

      Set the headlight lens LH in the middle of the headlight lens gasket as shown in the illustration.

    3. Check that the entire circumference of the headlight lens LH is positioned above the middle of the headlight lens gasket.

    4. Install headlight lens LH:

      Tech Tips

      Install the headlight lens LH to the headlight housing from the starting point of installation toward the inside of the vehicle as shown in the illustration.

      B006OU2C01
      *a Installation Starting Point - -
      B006N8A Install in this Direction - -

    5. Attach the base point claw.

    6. Attach the remaining claw to install the headlight lens LH.

      B006PWXC01
      *a Base Point Claw - -
    7. B006QZI

      Install the 9 screws.

    8. Check the condition of the headlight lens gasket.

      OK
      Gasket contacts headlight lens LH and does not protrude out.
    9. B006QEW

      Connect the connector.

    10. B006Q3AC01
      B006N8A Clockwise

      Set the connector cap into place and turn the connector cap clockwise until it stops to install it.

  5. INSTALL HEADLIGHT GASKET

    Click here

  6. INSTALL HEADLIGHT ECU SUB-ASSEMBLY LH

    Note


    • Prevention of static electricity is required during this procedure.

    • Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

    • If the headlight ECU sub-assembly LH has been dropped, replace it with a new one.

    • If the headlight ECU sub-assembly LH has been removed, replace the headlight gasket with a new one.

    • Perform work using clean rubber gloves.

    • Do not touch the headlight ECU sub-assembly LH connector with bare hands.

    SST
    09890-47010   ( 09891-04010, 09891-04020, 09891-04030, 09891-04040 )

    1. B006PHQ

      Connect the connector.

    2. B006PNG

      Install the headlight ECU sub-assembly LH with the 3 screws.

  7. INSTALL HEADLIGHT PROTECTOR LH


    1. B006PESC01
      B006PCE Area to Clean

      Clean the application area of the headlight protector LH shown in the illustration.

      Note

      Remove any remaining double-sided tape, and then clean and degrease the area.

    2. Remove approximately 3.0 cm (1.18 in.) of the peeling tape from a new headlight protector LH.

    3. Align the angle so that it is inside the application start position and while the headlight protector LH is contacting the flange, set the prepared peeling tape.

    4. Press the set portion of the part with your finger to secure it.

      Note

      Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.

      B006LTXC01
      *a Application Start Position *b Align angle with application start position, and then set into place
      *c Flange *d Set with the headlight protector LH contacting the flange
      B006N8A Press Here - -
    5. B006O6BC01
      *a Alignment Line
      B006N8A Install in this Direction

      While peeling the peeling tape, position the headlight protector LH so that it contacts the flange and set it to the application end position.

      Tech Tips

      Set the end point of the headlight protector LH so that it is between the two alignment lines.

    6. B006M7VC01
      B006N8A Press Here

      Press the set portion of the part with your finger to secure it.

      Note

      Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.

  8. INSTALL HEADLIGHT COVER LH


    1. B006MO4

      Attach the claw to install the headlight cover LH.