Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Data List / All Data.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Headlight Low Beam State | Low beam headlight state | ON or OFF | ON: Low beam headlights on OFF: Low beam headlights off |
- |
| Headlight High Beam State | High beam headlight state | ON or OFF | ON: High beam headlights on OFF: High beam headlights off |
- |
| DRL Operating State | Daytime running light state | ON or OFF | ON: Daytime running light on OFF: Daytime running light off |
The display is different depending on the destination. |
| Daylight Operating State | Daytime running light state | ON or OFF | ON: Daytime running light on OFF: Daytime running light off |
The display is different depending on the destination. |
| Clearance Light State | Clearance light state | ON or OFF | ON: Clearance light on OFF: Clearance light off |
- |
| Right Cornering Light State | Cornering light RH state | ON or OFF | ON: Cornering light RH on OFF: Cornering light RH off |
w/ Cornering Light |
| Left Cornering Light State | Cornering light LH state | ON or OFF | ON: Cornering light LH on OFF: Cornering light LH off |
w/ Cornering Light |
| +B | IG power supply voltage value | 0 to 19.75 V | 11 to 14 V | - |
| Height Sens Pw Supply Val | Height control sensor power supply value | 0.00 to 5.00 V | 4.61 to 5.00 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value | 0.00 to 5.00 V | 0.50 to 4.50 V | The value changes according to the vehicle height. |
| Front Right Wheel Speed Value | Front right wheel speed | 0.00 to 260.00 km/h (161.56 mph) | Condition can be displayed | - |
| Front Left Wheel Speed Value | Front left wheel speed | 0.00 to 260.00 km/h (161.56 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed | 0.00 to 260.00 km/h (161.56 mph) | Condition can be displayed | - |
| Rear Height Adjust Value | Rear height adjustment offset value | 0 to 1023 | Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed) | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range | Valid or Invalid | Valid: Rear vehicle height calibration not completed Invalid: Rear vehicle height calibration completed |
- |
| Init Writing Count | Number of times for initialization | 0 to 255 | Number of times for initialization | - |
| Sensor Initialization Hist | Sensor initialization history | not comp, 10%,25%, 50%, 75%,100% or complied | Condition can be displayed | - |
| Steering Sensor Signal | Steering angle sensor value | -384 to 382.5 deg | 0.0 deg | 0.0 deg is displayed when steering wheel is centered. |
| Steering Sensor Center Position | Steering angle sensor center position | -3072 to 3070.5 deg | 0.0 deg | 0.0 deg is displayed when steering wheel is centered. |
| +B Voltage Value | Headlight light control ECU power supply voltage value | 0 to 19.75 V | 11 to 14 V | - |
| Traveling Direction | Vehicle forward movement condition | Fwd or Not Fwd | Fwd: Vehicle moving forward Not Fwd: Vehicle not moving forward |
- |
| Leveling Motor Target Position | Leveling motor drive target position | 0 to 102.3% | 10.0 to 90.0% | - |
| Steering Sensor Initialization Status | Steering angle sensor initialization condition | Incomplete or Completed | Incomplete: Steering angle sensor initialization not completed Completed: Steering angle sensor initialization completed |
- |
| Number Of Trouble Codes | Number of trouble codes | 0 to 255 | Condition can be displayed | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Operates the headlight leveling motor (Perform with the vehicle stopped, engine running and low beam headlights illuminated) | Up, Down or Stop | - |